background image

Table of contents

Page 2 | 10

2008115 [Rev .1 - en]/2016-09-08

Table of contents

1

Introduction....................................................................................................................... 3

1.1

Information on safety.................................................................................................................................... 3

1.2

Information on the target group and application of these instructions......................................................... 3

1.3

Explanation of the signal words................................................................................................................... 3

1.4

Basic safety instructions............................................................................................................................... 3

2

Product information...........................................................................................................4

2.1

Parts description........................................................................................................................................... 4

2.2

Technical data...............................................................................................................................................4

2.3

Intended use................................................................................................................................................. 4

3

Operation.......................................................................................................................... 5

3.1

Product with motor........................................................................................................................................5

3.2

Incorrect operation........................................................................................................................................5

4

Maintenance......................................................................................................................6

4.1

Cleaning........................................................................................................................................................ 6

4.2

Maintenance..................................................................................................................................................7

4.3

Spare parts/repairs....................................................................................................................................... 7

4.4

Warranty........................................................................................................................................................7

5

Dismantling....................................................................................................................... 8

6

Troubleshooting.................................................................................................................9

7

EC Declaration of Conformity.........................................................................................10

Summary of Contents for Venetian 2.25/35.17











Reviews: