background image

Introduction

Page 4 | 10

2008115 [Rev .1 - en]/2016-09-08

Accessing the operating element (electrically operated

product)

The operating element is not intended for children to use.
Children are unable to recognize the danger associated
with the product. Persons can become injured from
careless use.

Do not allow children to play with the locally installed

control system or operating element.
The hand-held transmitter must be kept out of the reach

of children.

Risk of damage to the product

An additional load can damage the product and/or cause it
to detach from the wall.

It is not permitted to hold onto the product or to lean

objects against it.

2

Product information

2.1

Parts description

2

3

1

6

5

4

1

Top rail

4

Tension cable
(optional)

2

Slats

5

Tension cable bracket
(optional)

3

Tilting tape

6

Bottom rail

Fig. 1:

Venetian blind type 2.xx.17 inside

2.2

Technical data

Parameter

Value

Current consumption

0.30-0.32 A

Rated voltage

24 V DC

Degree of protection

IP 44

Short-term operation (S2)

4 min.

Noise emission level

< 70 dB(A)

*

*

In a standard installation of the product on a test
stand, the noise emission level is < 70 dB(A). This
value may vary depending on the installation.

INFO

The table above shows a summary of the
permissible motors.

2.3

Intended use

The following details apply to the following product:
venetian blind with 24-volt electric drive Type 2.25/35.17
inside

The product is an internal sun shading system that may be
used for glare control and to provide visual privacy. Visual
privacy and the view out can be individually regulated.

The product is installed on an inside wall or ceiling, either in
front of or inside the reveal.

The intended use also includes observing these instructions
and adhering to the service requirements they describe.

Summary of Contents for Venetian 2.25/35.17











Reviews: