background image

Troubleshooting

2008115 [Rev .1 - en]/2016-09-08

Page 9 | 10

6

Troubleshooting

INFO

Problems described here without a reference to

a qualified specialist or certified electrician may

be rectified independently.
All other problems described here are only to

be dealt with by a qualified specialist or certified

electrician.

Fault: The motor is not functioning

Cause

Remedy

Note

A higher-level control command is

present

Wait for on/off delay and then try

again.

No voltage is applied.

Check the power supply.

Have checked by a certified electrician.

Motor is faulty

Replace the motor.

Replacement by a qualified specialist

Fault: The product does not move to the desired limit position

Cause

Remedy

Note

The motor limit positions are incorrect Readjust the motor.

Adjustment by a qualified specialist

Fault: The order height has decreased

Cause

Remedy

Note

The lower limit position is incorrect.

Perform a RESET.

Readjust the lower limit position (see

setting instructions and wiring dia-

gram).

Adjustment by a qualified specialist

Fault: Slats can be adjusted, but venetian blind does not move up

Cause

Remedy

Note

The lifting cord is torn.

Replace the lifting cord.

Replacement by qualified specialist

Summary of Contents for Venetian 2.25/35.17











Reviews: