background image

Operation

Page 6 | 10

2008115 [Rev .1 - en]/2016-09-08

Danger of crushing, shearing and entanglement

While the product is

moving, keep persons

away from the product.
While the product is

moving, do not reach

between the moving

parts. Limbs can get

caught between or in

the moving parts and

may become crushed or

severed.

Products operated by

means of a control unit may

start moving at any time

and without prior notice. In-

form people, including chil-

dren, who may be located

in the vicinity of the product

about the danger involved

with the product to elimi-

nate the risk.

Gust of wind

With the window open or

tilted, a sudden draft can

damage the product.

4

Maintenance

Proper and regular cleaning and maintenance and the
use of original spare parts only are essential for fault-free
operation and a long service life.

INFO

When performing product maintenance or working
in the vicinity of the product, such  as when cleaning
windows, movement of the product must be
prevented.

A monitored, overriding locking mechanism must
prevent every kind of operation.

WARNING

Risk of injury from operation of the product when it is
out of view!

The product may unexpectedly start moving during
cleaning or maintenance.

De-energise the product and secure it against

being switched on again.

CAUTION

Risk of injury from falling from climbing aid!

Climbing aids (e. g. ladders, scaffolding etc.) may tip
over if improperly erected.

Position climbing aids on level and firm ground.

4.1

Cleaning

To ensure the longest possible life, we recommend
that you clean the surface of the product regularly or
at least once a year.

If the first cleaning takes place several years after
initial installation, the product or fabric cannot be
restored to its original condition.

Replacement claims cannot be honoured on the
grounds of these cleaning instructions because the
effectiveness of these measures depends on a large
number of factors that vary from case to case.

Always follow the manufacturer instructions when
using chemical cleaning products. In the interest of
the environment, it is recommended that you only
use 100% biologically degradable cleaning products.

Summary of Contents for Venetian 2.25/35.17











Reviews: