WAREMA WMS Weather Station Eco Operating And Installation Instructions Download

Page: 11 / 12

2024730_d•en•2020-01-01

We reserve the right to make technical modifications

Button

Action/result

> 10 s

Resetting the WMS weather station

The WMS weather station transmits a delete

command to the network and is reset to the

factory settings.

Press the

and

buttons simultane-

ously for at least 10 s.

The LEDs flash 5 times.

GREEN+RED: Reset and transmit delete

command

RED only:

Charge status too low, ac-

tion is not executed

All actuators and transmitters of the net-

work wave. The WMS weather station has

been deleted from the network and has

been restored to the factory settings and

will now be in learn mode for two minutes.

OTICE

When you delete sensors from the

network, they are deleted from all

reachable receivers in the network.

The control functions of the receiv-

ers remain active and must be

separately deactivated for each

receiver.

The radio module of the WMS weather station is acti-

vated for one minute every time a button is pressed if the

sensor is not set to factory settings.

Technical data

WMS weather station eco

min.

typ.

max.

Unit

Supply

Operating duration with full

buffer

(in darkness (0 lx))

days

Ready for operation when

connected via

USB charger:

imme-

diate

RF transceiver

Transmission frequency

2.40

2.48

GHz

Transmission power

dBm

Reception sensitivity

-101

dBm

Operating range

(environment without inter-

ference)

Readings

Wind speed

(intervals 0.5 m/s)

m/s

Brightness

(intervals 0.5 klx)

100

klx

Dawn/dusk

(intervals 2 lx)

500

Housing

Dimensions in mm

(LxWxH)

278 x 118 x 207 mm

Degree of protection

IP43

Safety class

III

Miscellaneous

Conformity

available at

www.warema.de/ce

This device meets the EMC directives for use in residential and

commercial areas.
WAREMA Renkhoff SE declares herewith that this radio system

type [WMS weather station eco] is in compliance with the cur-

rent guidelines.

Ambient conditions

Pollution degree

Operating and storage

temperature

-20

°C

Humidity

(not condensing)

100

rel

Degree of soiling

Article numbers

WMS weather station eco

2024 679

Accessories kit 3x VARTA

V65 HT NiMH coin cell

battery

2029 295

Optional accessories

USB plug-in power supply

unit

1002 879

Micro USB cable for plug-

in power supply unit

2004 192

WAREMA Renkhoff SE

Hans-Wilhelm-Renkhoff-Strasse 2

97828 Marktheidenfeld

Germany

Summary of Contents for WMS Weather Station Eco













Search results

Summary of Contents for WMS Weather Station Eco

Reviews:

Related manuals for WMS Weather Station Eco

Brands by name

Popular brands

WAREMA WMS Weather Station Eco, Operating And Installation Instructions

Search results

Summary of Contents for WMS Weather Station Eco

Reviews:

Related manuals for WMS Weather Station Eco

Brands by name

Popular brands