background image

2

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should 

always be followed, including the following:
 1. 

 READ ALL INSTRUCTIONS.

 2.  

Unplug from outlet when not in use, before putting on or 

taking off parts, and before cleaning. 

 

3.   To protect against risk of electrical shock, do not immerse 

main unit or power cord in water or other liquid.

  4.    Close supervision is necessary when any appliance is used by 

or near children. This appliance is not recommended for use by 

children.

  5.   Avoid contact with moving parts. Wait until moving parts have 

stopped running before you remove the parts of the appliance.

  6.   Never put the unit on or near a hot burner, in an oven, or in a 

dishwasher.

  7.    Do not operate the appliance, or any other electrical 

equipment, with a damaged cord or plug or after the appliance 

malfunctions, or is dropped or damaged in any manner. Return 

to the nearest authorized service center for examination, repair, 

or adjustment.

  8.   Never feed food by hand; always use the food pusher. Keep 

hands, hair, clothing and utensils away from moving discs 

during operation to reduce the risk of personal injury and/or 

damage to the appliance.

  9.   Do not use outdoors, or use for other than intended use.
 10.   Warning: the cutting blade is sharp; handle with care both 

when using and when cleaning.

 11.    Do not let cord hang over edge of table or counter, contact 

sharp edges, or touch hot surfaces.

 12.   Do not pull on the power cord to disconnect.
 13.   Never plug in the appliance where water may flood the area.
 14.   Place the appliance on a firm and stable surface.
 15.   NEVER PUT YOUR FINGERS NEAR THE FOOD CHUTE WHILE 

GRINDER IS IN OPERATION.

 16.   Ensure that the appliance is not placed close to the edge of the 

table, worktop, etc. where it can be pushed off or fall.

Summary of Contents for MG1200













Reviews: