background image

3

 17.   The use of attachments not recommended or sold by the 

manufacturer may cause fire, electric shock or injury.

 18.   Never use abrasive cleaning agents or abrasive cloths when 

cleaning the unit.

 19.   Do not use fingers to scrape food away from cutting blade 

while appliance is in operation. Cut-type injury may result.

 20.  Use the unit only when completely assembled.
 21.  Do not leave the appliance unattended while it is running.
 22.   Before using for the first time, remove all packaging and wash 

parts.

 23.   This appliance has a polarized plug (one blade is wider than 

the other). To reduce the risk of electric shock, this plug will fit 

in a polarized outlet only one way. If the plug does not fit the 

outlet perfectly, reverse the plug. If it should still not fit, contact 

a qualified electrician. Do not modify the plug in any way.

 24.   Check that the control is OFF before plugging the cord into 

wall outlet. To disconnect, turn the control to OFF, then remove 

plug from wall outlet.

 25.   Do not operate your appliance in an appliance garage or  

under a wall cabinet. 

When storing in an appliance garage, 

always unplug the unit from the electrical outlet.

 Not 

doing so could create a risk of fire, especially if the appliance 

touches the walls of the garage or the door touches the unit as 

it closes.

26.  DO NOT operate the grinder without the hopper in place. 
27 .  DO NOT attempt to grind bones, nuts, or other hard items. 
     This appliance is for 120 volts only and should not be used 

with a converter.

 

SAVE THESE INSTRUCTIONS 

FOR HOUSEHOLD USE ONLy

Summary of Contents for MG1200













Reviews: