background image

NOTICE:

 Customer is solely responsible for determining whether the 

products and the information contained in this installation guide are 
appropriate for Customer’s use and are in compliance with applicable laws 
because the applicable laws related to the installation and use of this 
product may vary from one location to another and may change with time.  
Customer represents and warrants that Customer is required to check 
current local laws, building codes and other local requirements and that all 
local requirements will be adhered to in connection with the installation of 
this product.  

NO EXPRESS WARRANTIES ARE GIVEN EXCEPT FOR ANY APPLICABLE 
WRITTEN WARRANTIES SPECIFICALLY PROVIDED BY WARMBOARD.  
ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY 
AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY 
EXCLUDED.  FAILURE TO INSTALL WARMBOARD PRODUCTS ACCORDING 
TO MANUFACTURER’S INSTRUCTIONS WILL VOID ALL APPLICABLE 
WARRANTIES.  IT IS EXPRESSLY UNDERSTOOD THAT WARMBOARD IS 
NOT RESPONSIBLE FOR ANY CONSEQUENTIAL OR OTHER DAMAGES 
THAT MAY ARISE FROM USING WARMBOARD PRODUCTS OR 
COMPONENTS.

Warmboard assumes no obligation or liability for the information contained 
in this document.  The Customer assumes all risks as to the use of this 
product.  Customer’s exclusive remedy or any claim (including any claim 
for negligence, strict liability, or tort, without limitation) shall be limited 
to the warranty coverage expressly provided in Warmboard’s warranty 
documents.  Failure to stringently adhere to any of the recommended 
procedures of this installation guide and/or any other Warmboard 
document related to this product shall release Warmboard of all liability 
with respect to this product or the use thereof. 

For complete warranty information please call 1.800.556.0595  
or visit warmboard.com

KEEP OUT OF REACH OF CHILDREN

Summary of Contents for Comfort System















Reviews: