background image

4

GENERAL WARNINGS

WARNING: YOU MUST READ OWNERS MANUAL IN ITS ENTIRETY PRI-

OR TO INSTALLATION AND/OR OPERATION. 
WARNING: FOR OUTDOOR USE ONLY. 
WARNING: Improper installation, adjustment, alteration, service, or 

maintenance can cause injury or property damage. Read the installation, 

operating, and maintenance instructions thoroughly before installing or 

servicing this equipment. 
WARNING: Do not store or use gasoline or other fl ammable vapors and 

liquids in vicinity of this or any other appliance. 
WARNING: LP-cylinder not connected for use shall not be stored in the 

vicinity of this appliance. 
WARNING: If you smell gas: 

•  Shut off gas to appliance. 
•  Extinguish any open fl ame. 
•  If gas odor continues, keep away from appliance and immediately 

call gas supplier or fi re department. 

WARNING: DO NOT USE OXYGEN MIXERS WITH CROSSFIRE

TM

 

BRASS BURNERS. Mixers create leakage in the cavity of the pit and are a 

serious hazard.
GENERAL INFORMATION
Carefully follow the instructions in this manual to prevent personal injury or 

property loss. Instructions are updated as needed. It is the installer’s respon-

sibility to periodically review instructions for applicable updates. 
WARNING: This Owner’s Manual contains critical information for the safe 

installation and operation of the fi re features listed in this manual.  All instruc-

tions must be strictly followed for safe installation and operation.  Warranty is 

void if not followed.
WARNING: It is the installer’s responsibility to ensure a safe installation and 

to educate the end user as to proper operation. Installer must leave this 

manual with the end user. 

WARNING: We suggest that our products be installed by professionals 

that are locally licensed by the authority having jurisdiction in gas piping. 

We suggest that our products be serviced annually by a licensed plumber.  

Installer must follow all instructions carefully to ensure proper performance 

and safety. Warming Trends

TM

 is not responsible for your actions. 

WARNING: Never alter product or confi guration in any way.  Alterations can 

damage the product and cause harm to the end user.  Warranty is void if any 

modifi cation is made to product.
WARNING: FOR REMOTE CONTROL USE: To prevent accidental startup 

from unwanted Remote Control signals it is the responsibility of the end user 

to turn off power to electric outlet for the remote-control receiver when the 

fi re-pit is not in use via wall switch or breaker. 
WARNING: Product is not intended to be a starter for wood or other combus-

tibles. 
WARNING: It is the responsibility of the installer to follow ALL LOCAL 

CODES concerning the installation and operation of the fi re pit. In the ab-

sence of local codes, please follow: 

•  Fixed piping system: The National Fuel Gas Code, ANSI Z223.1/

NFPA 54 or International Fuel Gas Code. 

•  Electrical ground: The National Electrical Code, ANSI/NFPA 70. 

WARNING: Only use gas/fuel type specifi ed for this fi re pit. See label on the 

burner. Verify correct gas/fuel type and pressure. Never use an alternative 

fuel, included but not limited to biofuel, ethanol, lighter fl uid or any other 

alternative fuel other than Liquid Propane or Natural Gas. 
WARNING: Gas pressure and type should be checked prior to use and 

installation. 

SELECTING A LOCATION FOR YOUR FIRE FEATURE

WARNING: All fi re pits, match lit kits, spark ignition, and electronic igni-

tion systems are designed and intended for outdoor use only. 
WARNING: For electronic ignition models, there must be an electrical 

shut off (wall switch or breaker) on the exterior of the fi re pit or on adja-

cent wall to allow for emergency shutdown and maintenance. Distance 

may be determined by local code.
WARNING: All fi re pits must have a gas shutoff located outside of the fi re 

pit to allow for emergency shut off and maintenance. 
WARNING: Select a location where the fi re pit can be attended during 

operation. Never leave an operating fi re pit unattended or by someone 

not familiar with its operation or emergency shut off locations. 
WARNING: Both children and adults should be alerted to the hazards 

of high surface temperatures and should remain a safe distance away to 

avoid burns and clothing ignition. 
WARNING: Young children should be carefully supervised when they are 

in the area of a fi re pit. 
WARNING: Clothing or other fl ammable materials should not be placed 

on or near fi re pit. 
WARNING: Fire pits create very high temperatures - Combustibles must 

be located far enough away that there is no risk of ignition. 
IMPORTANT: It is recommended that material such as granite, marble or 

other dense stone be kept an appropriate distance away from fl ame due 

to risk of cracking. Manufacturer is not responsible for damage to any fi re 

pit material for any reason. 

FIRE PIT CLEARANCES 

•  36” horizontally from any combustible structure.
•  Overhead clearance should be a minimum of 120” from com-

bustible structures.

•  Choose a location that allows easy access for installation and 

maintenance of the fi re pit.

•  Pick a location that allows suffi cient horizontal room to enjoy the 

fi re pit while allowing a safe distance from the heat and fl ame. 

•  Always consult with local municipality regarding any local code 

requirements

MATCH LIGHT

Minimum

Maximum

Natural Gas

3.5” W.C.

7.0” W.C.

Liquid Propane

11.0” W.C.

13.0” W.C.

3V - 3VIK

Minimum

Maximum

Natural Gas

4.5” W.C.

10.0” W.C.

Liquid Propane

11.0” W.C.

13.0” W.C.

STANDARD - 24VIKSC 

& 24VIKHC

Minimum

Maximum

Natural Gas

3.0” W.C.

5.0” W.C.

Liquid Propane

8.0” W.C.

12.0” W.C.

PREMIUM - P24VIKSC 

& P24VIKHC

Minimum

Maximum

Natural Gas

3.5” W.C.

14.0” W.C.

Liquid Propane

8.0” W.C.

14.0” W.C.

Summary of Contents for CFB60 2XL NG






























Reviews: