background image

PELLET STOVES                                                9                                                                 PS45B   041113-24

45

90

  

Vent Termination  Requirement

1. Do not terminate the vent in any enclosed or semi-enclosed 
areas such as a carport, garage, attic, crawlspace, narrow 
walkway, closely fenced area, under an enclosed sun deck or 
porch, or any location that can build up a concentration of fumes 
such as stairwells, covered breezeway, etc.

2. Termination must exhaust above the inlet elevation. It is 
recommended that at least fi ve feet of vertical pipe be installed 
in the vent system. This will create a natural draft to prevent 
the possibility of smoke or odor during appliance shut down or 
power failure and avoid exposing people or landscaping shrubs 
to high temperatures.

Hooded vent

 

Using existing 
wood vent

Thru -roof 

Recommended

Recommended

Recommended

Fig #6

Storm collar

Roof fl ashing

Rain Cap

5ft
(150cm) 
rise

CAUTION
This Installation may 
cause problems during 
adverse weather or power 
failure.

3 Vent surfaces can become hot enough to cause burns if touched. 
Non-combustible shielding or guards may be required.

4. The Vent must terminate a minimum of 12 inches (30 cm) 
from the wall. Vertical termination must protrude a minimum of 
24" (60 cm) from the roof surface.

5. Locate the vent termination at least two feet away from 
combustible materials such as shrubs, plants, grass, fences, 
roof overhangs and adjacent buildings.

Summary of Contents for PS45 series A

























Reviews: