background image

2

Contents

Contents

Do’s and don’ts
Selecting the correct heater 
What you need for installation
Floor coverings
Safety - electrical considerations
Subfloor preparation
About the mat
Testing the mat
Sizing guide
How you can modify the mat
Installation
Control card
Warranty

3

4

5

6

7

10

Your Warmup Underfloor heating mat 

has been designed so that installation 

is quick and straight forward, but as 

with all electrical systems, certain 

procedures must be strictly followed. 

Please ensure that you have the 

correct heater(s) for the area you wish 

to heat.

Warmup plc, the manufacturer of the 

Warmup Undertile Heating System, 

accepts no liability, expressed or 

implied,

for any loss or consequential damage 

suffered as a result of installations 

which in any way contravene the 

instructions

that follow.

It is important that before, during and after installation that all requirements are 

met and understood. 

If the instructions are followed, you should have no problems. If you do require 

help at any stage, contact our helpline: 

0845 345 2288 

You may also find a copy of this manual, wiring instructions and other helpful 

information on our website: www.warmup.co.uk 

11

Summary of Contents for PVC













Reviews: