background image

WARN INDUSTRIES 

PAGE 1 

61584 Rev C0 

 

 
 
 
 
 
 
 
 

 

WARNING

 

SEVERE INJURY OR DEATH MAY RESULT IF YOU IGNORE ANY OF THE 
FOLLOWING.

 

 

Read the Winch Operator’s Manual, ATV Operator’s Manual, and all warning labels 
before operating the winch and ATV. 

 

Stay clear of moving parts and cable.  Keep others away when operating the winch. 

 

Inspect the winch mechanism, fasteners, and cable, before operating.  Replace all worn 
or damaged parts before operating. 

 

Make sure the winch is deactivated when leaving the ATV unattended.

 

 

PARTS LIST: 

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided installation 
and operating instructions and other information on labels and in this guide. This information alerts you to potential hazards that could 
hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good 
judgment.

  

CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. 
READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING 
AND OPERATING THIS PRODUCT. 

This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or death. 

WARNING

 and 

CAUTION

 are signal words that identify the level of hazard. These signal words mean:  

 WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations. 

CAUTION signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.

  

This guide uses 

NOTICE

 to call attention to important mechanical information, and 

Note:

 to emphasize general information worthy of 

special attention. 

PART  NO.

 

QUANTITY DESCRIPTION

 

22262 

5/16” Flat Washer 

1402 

5/16” Lock Washer 

3870 

5/16-18 x ¾” Hex Bolt 

2079 

5/16-18” Hex Nut 

1320 8 

¼” 

Washer 

1321 

¼” Lock Washer 

1322 

¼” Hex Nut 

37205 

¼ x 20 x 1 x 1-3/4x 1” U-Bolt 

22508 

Capscrew, Hex, 8mm x 1.25 x 25mm 

61585 1 

Front 

Bracket 

61648 

Center Rear Bracket 

61582 

Left Rear Bracket 

61583 

Right Rear Bracket 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTALLATION INSTRUCTIONS

ATV WINCH MULTI-MOUNT

 

Multi-Mount Mounting-Kit:  PN 61019 

Application: HONDA RUBICON 

 

Summary of Contents for 61019








Reviews: