background image

Warranty

Warner Electric LLC warrants that it will repair or replace (whichever it deems advisable) any product 
manufactured and sold by it which proves to be defective in material or workmanship within a period of one (1) 
year from the date of original purchase for consumer, commercial or industrial use .

This warranty extends only to the original purchaser and is not transferable or assignable without Warner Electric 
LLC’s prior consent .

Warranty service can be obtained in the U .S .A . by returning any defective product, transportation charges 
prepaid, to the appropriate Warner Electric LLC factory . Additional warranty information may be obtained by 
writing the Customer Satisfaction Department, Warner Electric LLC, 449 Gardner Street, South Beloit, Illinois 
61080, or by calling 815-389-3771 .

A purchase receipt or other proof of original purchase will be required before warranty service is rendered . If 
found defective under the terms of this warranty, repair or replacement will be made, without charge, together 
with a refund for transportation costs . If found not to be defective, you will be notified and, with your consent, the 
item will be repaired or replaced  and returned to you at your expense .

This warranty covers normal use and does not cover damage or defect which results from alteration, accident, 
neglect, or improper installation, operation, or maintenance .

Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply 
to you .

Warner Electric LLC’s obligation under this warranty is limited to the repair or replacement of the defective 
product and in no event shall Warner Electric LLC be liable for consequential, indirect, or incidental damages of 
any kind incurred by reason of the manufacture, sale or use of any defective product . Warner Electric LLC neither 
assumes nor authorizes any other person to give any other warranty or to assume any other obligation or liability 
on its behalf .

WITH RESPECT TO CONSUMER USE OF THE PRODUCT, ANY IMPLIED WARRANTIES WHICH THE 
CONSUMER MAY HAVE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL 
CONSUMER PURCHASE . WITH RESPECT TO COMMERCIAL AND INDUSTRIAL USES OF THE PRODUCT, 
THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES, WHETHER 
EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, 
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS .

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above 
limitation or exclusion may not apply to you . This warranty gives you specific legal rights and you may also have 
other rights which vary from state to state .

Changes in Dimensions and Specifications

All dimensions and specifications shown in Warner Electric catalogs are subject to change without notice . 
Weights do not include weight of boxing for shipment . Certified prints will be furnished without charge on request 
to Warner Electric .

P-273-5-WE    819-0529     12/18

www.warnerelectric.com

31 Industrial Park Road

New Hartford, CT 06057

815-389-3771

Summary of Contents for EM-50















Reviews: