Warren rupp SANDPIPER G Series Original Instructions Manual Download

Page: 15 / 18

Gas Valve Assembly Parts List

Item Part Number

Description

Qty

031.203.000

Assembly, Gas Valve

031.039.000

Sleeve & Spool Set

095.113.157

Body, Valve

1C 132.037.357 Bumper

165.129.157

Cap, End

170.032.330

1/4-20 X 3/4 Capscrew

560.058.360

7/8 ID X 1/16 CS O-Ring

Gas Valve Assembly Parts List with FKM O-rings

Item Part Number

Description

Qty

1 031.203.363

Assembly, Gas Valve

1A 031.039.000

Sleeve & Spool Set

1B 095.113.157

Body, Valve

1C 132.037.357

Bumper

1D 165.129.157

Cap, End

1E 170.032.330

Cap Screw, Hex 1/4-20 x .75

1F 560.058.363

O-ring 7/8 ID x 1/16 CS

Pilot Valve Assembly

PILOT VALVE ASSEMBLY PARTS LIST

WITH NITRILE O-RINGS

Item

Part Number

Description

Qty

095.074.558

Pilot Valve Assembly

095.071.558

Pilot Valve Body

755.025.148

Pilot Valve sleeve

560.033.360

O-Ring

775.014.115

Pilot Valve Spool

560.023.360

O-Ring

675.037.080

Retaining Ring

Pilot Valve Servicing

With Pilot Valve removed from pump.

Step 1:

Remove snap ring (4F).

Step 2:

Remove sleeve (4B), inspect O-Rings (4C),

replace if required.

Step 3:

Remove spool (4D) from sleeve (4B),

inspect O-Rings (4E), replace if required.

Step 4:

Lightly lubricate O-Rings (4C) and (4E).

Reassemble in reverse order.

LEGEND:

= Items contained within Gas End Kits

= Items contianed within Wet End Kits

Note:

Kits contain components specific to the material codes.

PILOT VALVE ASSEMBLY PARTS LIST

WITH FKM O-RINGS

Item

Part Number

Description

Qty

095.074.363

Pilot Valve Assembly

095.071.558

Pilot Valve Body

755.025.363

Pilot Valve Sleeve

4C 560.033.363

O-ring

4D 775.014.363

Pilot Valve Spool

560.023.363

O-ring

675.037.080

Retaining Ring

g10fmdl1sm-rev1218

sandpiperpump

com

Model G10F •

MODEL SPECIFIC

4: GAS END

Summary of Contents for SANDPIPER G Series



















Search results

Summary of Contents for SANDPIPER G Series

Reviews:

Related manuals for SANDPIPER G Series

Brands by name

Popular brands

Warren rupp SANDPIPER G Series, Original Instructions Manual

Search results

Summary of Contents for SANDPIPER G Series

Reviews:

Related manuals for SANDPIPER G Series

Brands by name

Popular brands