background image

pb025nmdl4sm-rev1119

sandpiperpump

.

com

14

 • Model PB¼ Non-Metallic

Main Air Distribution Valve and Pilot Valve

1.2

1.1

1.1

1.4

1.4

1.3

1.5

6

28

4

11

1.4

26

3

17

28

5

15

10

21

27.1

27

26.1

1.3

1.5

Air Distribution Valve Servicing

See repair parts drawing, remove screws.

Step 1:

 Remove end cap retainer (1.5).

Step 2:

 Remove end cap (1.3).

Step 3:

 Remove spool part of (1.1) (caution: do not scratch).

Step 4:

 Press sleeve (1.1) from body (1.2).

Step 5:

 Inspect O-Rings (1-4) and replace if necessary.

Step 6: 

Lightly lubricate O-Rings (1-4) on sleeve (1.1).

Step 7:

 Press sleeve (1.1) into body (1.2).

Step 8: 

Reassemble in reverse order, starting with step 4.

Note: Sleeve and spool (1-1) set is match ground to a specified 

clearance. Sleeve and spools (1-1) cannot be interchanged.

Pilot Valve Servicing

With Pilot Valve removed from pump.

Step 1: 

Remove snap ring (21).

Step 2: 

Remove sleeve (26), inspect O-Rings (26.1),

replace if required.

Step 3:

 Remove spool (27) from sleeve (27.1),

inspect O-Rings (3E), replace if required.

Step 4: 

Lightly lubricate O-Rings (26.1) and (27.1).

Reassemble in reverse order.

Main Air Valve Assembly Parts List

Item     Part Number    Description 

Qty

1          031.107.551      Valve, Main Air 

  1

1.1       031.106.000      Sleeve and Spool Set (Includes O-Rings) 

  1

1.2       095.077.551      Body, Air Valve 

  1

1.3       165.074.551     Cap, End, Air Valve 

  2

1.4       560.101.360     O-Ring

  8

1.5       675.051.115     Ring, Retaining 

  2

ATEX Compliant 

IMPORTANT

Read these instructions completely, before installation 

and start-up. It is the responsibility of the purchaser 

to retain this manual for reference. Failure to comply 

with the recommendations stated in this manual will 

damage the pump, and void factory warranty.

Main Air Valve Assembly Parts List

Item     Part Number    Description 

Qty

1          031.107.503      Valve, Main Air (Conductive Acetal)  

  1

1.1       031.106.000      Sleeve and Spool Set (Includes O-Rings) 

  1

1.2       095.077.503      Body, Air Valve 

  1

1.3       165.074.503     Cap, End, Air Valve 

  2

1.4       560.101.360     O-Ring

  8

1.5       675.051.115     Ring, Retaining 

  2

Pilot Valve Assembly Parts List

Item     Part Number    Description

Qty

21        675.047.115      Ring, Retaining  

1

26        755.038.000      Sleeve, Pilot Valve (Includes O-Ring) 

1

26.1     560.066.360      O-Ring

6

27        775.038.000      Spool, Pilot Valve (Includes O-Ring) 

1

27.1     560.029.374      O-Ring

6

4: AIR 

END

Summary of Contents for Sandpiper PB 1/4




















Reviews: