WINCH MANUAL
IMpORTANT SAFETY INSTRUCTIONS
4
NOTICE
The vehicle engine should always be kept running during winching
operation to minimize battery drain and maximize power and speed
of the winch. If the winch is used for a considerable amount of time
with the engine switched off the battery will drain and be too weak to
restart the vehicle engine. If this happens stop winching immediately,
jump start the vehicle and charge the battery up before resuming
winching operation.
NOTICE
Get to know your winch before you need to use it. We recommend
that you set up a few test runs to familiarize yourself with rigging
techniques; the sounds your winch makes under various loads and the
way the cable spools on the drum, etc.
INSPECT the wire rope and equipment before each use. A
frayed or damaged rope must be replaced immediately. Use
only manufacturer’s identical replacement rope with the exact
specifications. (Ropes are not covered by any warranty offered)
INSPECT the winch installation and bolts to ensure that all bolts are
tight before each operation or periodcally.
NOTICE
Store the remote control lead inside your vehicle or in a safe place.
Never connect the winch cable back to itself. This will cause cable to
damage. Always use a pulley, snatch block, sling or chain of suitable
strength as shown in the illustrations.
NOTICE
Any winch that appears to be faulty, damaged, worn, or operates
abnormally MUST BE REMOVED FROM SERVICE UNTIL REPAIRED,
REPLACED OR OVERHAULED. It is recommended that the necessary
repairs ARE made by a manufacturer’s authorized repair facility ONLY.
NOTICE
Pull only on areas of the vehicle as specified by the vehicle
manufacturer.
– Only accessories, attachments and/or adapters supplied by the
manufacturer shall be used.
CAUTION
When using the tool, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to the
equipment. Read all these instructions before using this tool!
WARNING
Keep children away. Children must never be allowed in the work area,
Do not let them handle machines, tools, extension cords or operate
this tool.
WARNING
Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Always lock up tools and keep out of reach of
children.
CAUTION
Dress properly. Do not wear loose clothing or jewelry as they can
be caught in moving parts. Protective, electrically non-conductive
clothes and non-skid footwear are recommended when working.
Wear restrictive hair covering to contain long hair.
WARNING
Use eye and ear protection. Always wear impact safety goggles. Wear
a full-face shield if you are producing metal filings or wood chips.
Wear a dust mask or respirator when working around metal, wood,
and chemical dusts, and mists.
CAUTION
Maintain this winch with care. Keep this tool dry and clean for
better and safer performance. Follow instructions for lubricating
and changing accessories. Inspect winch rope periodically and,
if damaged, have them replaced immediately by an authorized
technician. The handles must be kept clean, dry, and free from oil and
grease always.
Disconnect or unplug remote switch when not in use.
DANGER
Stay alert, watch what you are doing, use common sense. Do not
operate any tool when you are tired.
WARNING
Check for damaged parts
. Before using this winch, any parts that
appear worn or damaged should be carefully checked to determine
that it will operate properly and perform to its intended function.
Check for damage including alignments, binding of moving parts;
mounting fixtures. Any part that is damaged should be properly
repaired or replaced by a qualified person. Do not use the tool if any
switch does not turn “On” and “Off” properly.
WARNING
Replacement parts and accessories.
When repairing or servicing,
only use identical replacement parts. The use of any other parts will
void the warranty.
Summary of Contents for S2500EN
Page 15: ...Winch Manual SPECIFICATIONS 15 WINCH ASSEMBLY DRAWING 40 39 38 36 41 37 43 42 S4000EN...
Page 18: ...Winch Manual SPECIFICATIONS 18 WINCH ASSEMBLY DRAWING 40 39 38 36 41 37 43 42 S5250...
Page 21: ...Winch Manual SPECIFICATIONS 21 WINCH ASSEMBLY DRAWING 39 38 37 35 40 36 42 41 S6000EN...