background image

 

18 

Limited lifetime with 3 year on electrical 

Limited Lifetime Warranty for WARRIOR WINCHES 

 

Winch solutions are the sole distributors of WARRIOR WINCHES. 

Winch solutions (“seller” or winch solutions) warrants to the original retail buyer only (“Buyer”) that any mechanical component of 
a genuine WARRIOR WINCH (“product”) is free of defects in material and workmanship for the lifetime of the winch. 

 The electrical components (including the motor, contactor, and switches) will be free of defects in material and workmanship for a 
period of (3) three years (36 Months) from the original purchase provable date of purchase.  

Any  Product  Winch  solutions  determines  to  be  defective  will  be  repaired  or  replaced  at  Winch  solutions  sole  discretion  without 
charge to the Buyer upon Buyer’s compliance with this procedure. Seller or its Authorized Agent may make reasonable charges 
for  parts  and  for  labour  for  repairs  not  covered  by  this  Lifetime  Limited  Warranty.  The  warranties  set  forth  herein  are  exclusive 
and in lieu of all other warranties, whether oral or written, express or implied. 

All  purchases  must  be  registered.  Any  product  that  has  not  been  registered  will  be  covered  by  the  standard  1  year 
warranty. 

To obtain service under this warranty, the Buyer shall mail, ship or otherwise deliver to the address noted below, at the Buyers 
expense; (1) the Product, (2) a written description of the problem, (3) Buyers name, address and contact number, (4) copy of the 
original purchase receipt. 

The Warranty does not cover the cost of labour or transportation/shipping charges for the replacement or installation of defective 
parts.  

This  warranty  does  not  apply  to  defects  of  the  Product  caused  by;  (1)  normal  wear  and  tear,  (2)  failure  to  comply  with  any 
installation  or  maintenance  instructions  provided  by  the  Seller,  including  but  not  limited  to  subjecting  the  product  to  loads  in 
excess of the loads listed in any instructions, Owners Manual or as detailed upon the Sellers website, (3) commercial or industrial 
use,  (4)  alteration  or  modification  by  any  parties  other  than  the  Seller,  (5)  misuse,  abuse,  neglect,  accidents,  Acts  of  God, 
terrorism or (6) other causes beyond the control of the Seller after delivery of the Product to the Sellers Authorized Agent.  

This Warranty does not cover cables, synthetic ropes, fairleads or exterior finishes 

Winch solutions shall not be responsible or liable for any indirect or consequential damages. These consequential damages may 
include, but are not limited to, lost profits or loss of use and down time. 

A winch solution reserves the right to change the Product design without notice. A winch solution reserves the right to replace any 
part or whole unit with a newer design of the same function. 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 20SPA12






















Reviews: