2 Remove the cylinder head
according section 12.2.1.
3 Mount the fastening tool
for cylinder liner 800123, see
Fig 10-4.
4 Remove the anti-polishing ring.
Insert the tool 800009
in the cylinder, by cranking the engine, the piston pushes the
anti-polishing ring out, see Fig 11-3.
5 Clean the threaded hole(s)
in the piston crown and fasten
the lifting tool 800012 by using the hexagon screws M12
×
40 (6).
6 Turn the crankshaft to the BDC
the cylinder concerned.
7 Open the upper connection
by lifting the distance
sleeves and the hydraulic tools in to position, see Fig 11-3.
8 Connect the hoses
of the hydraulic pump 800053 and pro-
ceed to open the upper connection as described in adjacent figure.
9 Strain the screws by raising the pressure
to the value
stated in the section 07.3 and proceed with opening the nuts.
Piston and connecting rod assembly
Hydraulic oil
DISMANTLING
1. Lift the distance sleeve.
2. Lift the hydraulic cylinder and
screws in a one package in pos.
3. Connect hoses, open valve.
4. Tighten the tool assembly,
until the piston and cylinder is
on the same level, open the
nuts by 180˚.
5. Close the valve, pump to
required pressure.
Open the nuts about half a turn.
6. Open the valve slowly and
remove the tool.
View C
C
Cyl. nr.
800010
800012
800013
800020
800020
Cyl. nr.
7
6
800009
800010 Assembly tool for piston
800012 Lifting tool for piston
800013 Clamp device for piston rings
800020 Hydraulic tightening tool
for connecting rod nuts
7. Securing ring
6. Screw
800009 Dismounting tool for
antipolishing ring
Fig 11-3
4011059601
32-200020
Crank Mechanism: Crankshaft, Connecting Rod, Piston
11
WÄRTSILÄ 32
11 - 5
Summary of Contents for PAAE051728
