background image

SWITCH BASE WIRING

MOUNTING

Parts List

QTY

DESCRIPTION

PT#

ITEM

1

P CLIP

600 30173

1

1

HOSE DRAIN PUMP 2.5M

600 60105

2

1

22MM 2 POLE DRAIN SWITCH

600 30517

3

1

BASE CONNECTOR FOR 2 POLE SWITCH

600 30542

4

1

ASSY DRAIN PUMP FILTER

400 10021

5

1

GASKET DRAIN PUMP UNION

38824

6

1

DRAIN PUMP UNION

38823

7

265x140mm

HOSE UPPER WASH XU3 (CUT TO LENGTH)

600 60523

8

4

HOSE CLAMP ASS16 

ASS16

9

1

DRAIN PUMP B20-6 220-240V 50Hz

600 60102

10

1

WASHER SPRING SS 304 1/4 inch (M6)

8566

11

1

MS HX SS 304 M6 X 16

600 80015

12

1

25mm ADHESIVE CABLE TIE MOUNT

3208

13

400 90174 16/02/2018

1-B

KIT0440072 - XP3 DRAIN PUMP RETROFIT

REV

1

2

3

9

10

8

7

6

5

CONNECT 
YELLOW/BROWN

CONNECT
BLACK

CRITICAL:
ENSURE ARROW ON BODY
ALIGNED WITH "TOP" 
MARKING ON SWITCH.
PUSH ON FIRMLY.

11

12

1.

Preassemble drain pump (10) with inlet hose (8) and outlet hose (2) using 

supplied hoseclips (9).

2.

Secure pump to base using M6 bolt (12) and spring washer (11).

3.

Assemble union (7) with gasket (6) onto machine waste connection. Join to 

inlet hose and fit hoseclip. Inside wash tank, place filter (5) over waste 

connection and refit upstand.

4.

Secure drain hose above water level using P clip (1) or cable tie mount(13).

5.

On machine control panel, find circular knockout in panel below 

temperature gauges. Trim label to suit and remove knockout. Fit switch (3). 

Some filing may be required to remove knockout tabs.

6.

Wire pump as shown - wires supplied in loom. Attach switch base (4) to 

drain switch, and connect bullets into loom wires. See schematic for detail.

7.

Once fitted - ensure that drain pump operates and light turns on when 

button is pressed. Ensure that drain pump operates during cycle.

 

JOIN BROWN WIRE
TO YELLOW/BROWN LOOM WIRE

JOIN BLACK WIRE
TO BLACK LOOM WIRE

LINK BROWN
AND WHITE WIRES

JOIN BLUE WIRES TO 
RED LOOM WIRE

JOIN RED WIRE TO BROWN LOOM WIRE

4

13

ARROW ON
THIS SIDE

FRONT

MOUNT PUMP
 HERE

NC

NO

C

INSULATE END OF RED WIRE

Service Manual XP3

40

Revision 1F

Summary of Contents for XP Series













































Reviews: