background image

1

N718W  7/99

TTA

AB

BLLEE  O

OFF  C

CO

ON

NTTEEN

NTTSS

718W

II

N

NSSTTA

ALLLLA

ATTIIO

ON

N

G

G

U

UIID

DEE

Directed Electronics, Inc.

®

What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Determining Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . 3

Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Wire Connection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Transmitter/Receiver Learn Routine  . . . . . . . . . . . . . . . . . . . . . . . . 4

To Enter the Transmitter/Receiver Learn Routine . . . . . . . . . . . . . 4

Operation Settings Learn Routine . . . . . . . . . . . . . . . . . . . . . . . . . . 4

To Enter the Operation Settings Learn Routine. . . . . . . . . . . . . . . 5

Feature Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Shock Sensor Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

To Adjust the Warn Away Level . . . . . . . . . . . . . . . . . . . . . . . . . . 6
To Test and Adjust the Current Warn Away Setting . . . . . . . . . . . . 6
To Adjust the Shock Sensor Full Trigger . . . . . . . . . . . . . . . . . . . . 7
To Test and Adjust the Current Full Trigger Setting . . . . . . . . . . . . 7

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8

Summary of Contents for 718W









Reviews: