background image

 

 
 
 

WWS800/850 Bluetooth Wireless Scanners 

 

User’s Manual 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 

 

 
 

WARNING 

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try correct the 
interference by one or more of the following measures: 

• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help. 

 
If applicable, as below 
 
FCC Caution: To assure continued compliance, (example – use only shielded 
interface cables when connecting to computer or peripheral devices). Any changes 
or modifications not expressly approved by the party responsible for compliance 
could void the user’s authority to operate this equipment. 
This transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter. 
 
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with 
minimum distance 20 cm between the radiator & your body. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation. 

Summary of Contents for WWS800























Reviews: