background image

 3.1 

Potential Dangers

Risk of injury:  The trimmer’s rotating parts and the grinding disc are 

dangerous.

Also the tip of the brush spindle could cause injury.

 4  Responsibility for Operation or Damage

The responsibility for operating the device lies exclusively with the owner or user if said 

device is incorrectly serviced, maintained or altered by persons not employed by an 

authorised dealer or if the device is used in a manner contrary to its specified purpose.

The unit has to be maintained and operated in accordance with this user manual. 

Wassermann Dental-Maschinen GmbH is not responsible for damage arising from the 

nonobservance

 of these instructions.

Warranty and responsibility provisions contained in the sales and supply conditions of 

Wassermann Dental-Maschinen GmbH are not extended by these instructions.

Responsibility for the product becomes void if alterations are made to it by

third parties or if non-approved parts are installed. Only original 

WASSERMANN parts should be used. If any damage results from the 

installation of a non-approved disc, responsiblity lies with the person 

installing that spare disc.

If diamond grinding discs are used, serious wear will result from grinding 

embedded materials and metals. We will be in no way responsible in this 

case.

6

Summary of Contents for HSS-ZA





















Reviews: