background image

5. ATTACHING DISCHARGE ELBOW

A.

Connect waste elbow to the disposer, proceed 

to step 6 and then connect bottom of the elbow
by  tightening the slip nut.

B.

Make sure all plumbing connections are tight 

and in accordance with all plumbing codes and 
ordinances. Run water and check for leaks.

6. CONNECTING DISPOSER TO MOUNT ASSEMBLY.

7. OPERATING INSTRUCTIONS

A.

Press firmly around the Hush Cushion

®

to ensure

it is engaged with the neck of the disposer.

B.

Lubricate the top inside lip of the rubber 

Hush Cushion

®

with a liquid soap.

C.

Line up discharge elbow of disposer with trap 

under mounting assembly. Guide disposer up and
engage the 

GROOVE

of the Hush Cushion

®

around the 

RIDGE

at the bottom of the sink flange

(see 6A & refer back to 3B). While still supporting
the disposer, tighten the screw-clamp around Hush
Cushion

®

. The disposer will now hang by itself.

D.

If you need to turn the disposer make sure the 

sink flange does not turn. It will break the seal 
created when installed. Go back to steps 5A and 5B.

A.

Remove sink stopper. Turn on a medium flow of

cold water.

B.

Turn switch to ON position; your motor is turning 

at full speed and ready to use.

C.

Scrape in food waste. Down the drain go table 

scraps, peelings, cobs, rinds, seeds, pits, small 
bones and coffee grounds. To speed up food 
waste disposal, cut or break up large bones,
rinds and cobs. Large bones and fibrous husks
require considerable grinding time and are more
easily thrown away with other trash. Do not be
alarmed that the disposer slows down while
grinding. The disposer is actually increasing
torque (grinding power) and is operating under
normal conditions.

D.

Before turning disposer off, let water and disposer

run for approximately 15 seconds after shredding

RUBBER GASKET

The Anti-Jam Swivel Impellers make a clicking sound as they swing into place. This indicates normal operation.

stops. This assures that all waste is thoroughly 
flushed through trap and drain.

E.

It is not recommended to use hot water while 

running disposer. Cold water will keep waste and
fats solid so disposer can flush away particles.

TIPS 

A.

You may want to leave the stopper in the drain 

when not in use to prevent utensils and foreign 
objects from falling into the disposer.

B.

Your disposer is ruggedly built to give you many 

years of trouble free service. It will handle all 
normal food wastes, but it will NOT grind and 
dispose of such items as tin cans, bottles or bottle
caps, glass, china, leather, cloth, rubber, string,
clam and oyster shells, or feathers.

6A

5A

5B

TRAP

SINK FLANGE
RIDGE

5C

HUSH
CUSHION

Summary of Contents for WLC-100









Reviews: