9) When controlling the motion detection function, connect to
⑩
I/O
CONNECTOR after wiring using the attached cable. See the pin
configuration as follows.
PIN No.
Cable color
Title
Function
1
Brown
MD_O
Alarm out
2
Black
GND
Camera GND
3
-
NC
Alarm output terminal
When the motion detection function is used, the alarm output terminals
1 and 2 are hot during detection of movement in the monitored area. If
an LED is connected as shown in the diagram below, the alert turns on
the LED by voltage output of 3.3V at maximum current of 6mA.
Options
To purchase these options, please contact the distributor or dealer from
which you purchased the WAT-910HX3/RC.
关于电子信息产品污染控制标识
Specifications
Contact information
Watec Co., Ltd.
Add.:
254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,
Yamagata-Ken, 997-0017 Japan
TEL: +81-235-23-4400 FAX: +81-235-23-4409
Email: info-o@watec.co.jp
URL: http://www.watec.co.jp
Model
WAT-910HX3/RC
(EIA)
Pick-up Element
1/3 inch interline transfer CCD image sensor
Number of Total Pixels
811(H) × 507(V)
Number of
Effective Pixels
768(H) × 494(V)
Unit Cell Size
6
.4μm(H) × 7.5μm(V)
Sync. System
Internal
Scanning System
2:1 Interlace
Video Output
Composite Video, 1.0 V(p-
p), 75Ω (Unbalanced)
Resolution (H)
More than 570TVL (Center)
Minimum Illumination
0.000003lx. F1.4
(Shutter: x256, AGC: HIGH,
γ
: 0.35, 3DNR ON)
S/N
More than 52dB (AGC=6dB,
γ
=1.0)
Function settings
OSD (On Screen Display) operated by remote control
Electronic iris
1/60-1/100000 sec.
x256(field) *selectable -1/100000 sec.
Electronic shutter
x2, x4, x8, x16, x32, x64, x128, x256 (field)
1/60, 1/100 sec.
1/250, 1/500, 1/1000, 1/2000,
1/5000, 1/10000, 1/100000 sec.
AGC
ON
LO: 6
30dB / MID: 6
34.5dB / HI: 6
41dB
OFF
6-41dB (1dB step) *selectable
Gamma Characteristics
γ
≒
0.05-1.00 (0.05 step), USER *selectable
Noise Reduction
3DNR ON *selectable / OFF
Wide Dynamic Range
USER1 / USER2 / OFF
Motion Detection
Max. 4 areas selectable (Out-put terminal available)
Lens-iris
Video / DC (EIAJ arrangement, Auto-select)
Back Light
Compensation
OFF / BLC / HSBLC
White blemish
correction
Up to 64 dots correctable by OSD operation
Power Supply
DC+12V
±
10%
Power Consumption
1.26W (105mA)
Operating Temperature
-10
-
+50
℃
Operating Humidity
Less than 95% RH (Without condensation)
Storage Temperature
-30
-
+70
℃
Storage Humidity
Less than 95% RH (Without condensation)
Lens Mount
CS-mount (Back focus adjustable)
Size
35.5(W)
36(H)
63.5(D) (mm)
Weight
Approx. 81g
Design and specifications are subject to change without notice.
Watec is not responsible for any inconvenience or the attendant damages
to the video and monitoring recording equipment caused by misuse,
mis-operation or improper wiring of our equipment.
If for any reason the WAT-910HX3/RC does not work properly, or if you
have any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased.
C-mount Adaptor (30CMA-R)
This lens mount adaptor is used to
convert a CS-mount to a C-mount.
Mini Stand (MS50)
A convenient stand for the
WAT-910HX3/RC. With this stand,
the camera can be adjusted to
any desired angle.
1543Z00-Y2000001
