27
1
All CareSoft Elite RC and CareSoft Pro RC water conditioners are factory preset at medium salting.
2
Iron removal may vary depending on form of iron, pH and other local conditions. On waters that are pre-
chlorinated, or where other pre-oxidation occurs, an iron precipitate can form that is too small to be filtered.
3
Unit not tested for capacity at these peak flow rates. Water quality may vary.
*
CSERC and CSPRC units are not certified by WQA.
* All above water softeners are set at “minimum salting” from the factory.
Cabinet dimensions represent the High-Profile cabinet option. Low-Profile cabinets are about one inch shorter in
height than the High-Profile cabinet lid.
Cycle Times
(in minutes)
CareSoft Elite
®
and CareSoft Pro
®
Specifications
Manufactured for WaterCare • 1900 Prospect Court • Appleton, WI 54914 • Phone: 920-739-9401 • Fax: 920-739-9406
SPE-WC SOFT RevA0520
MODEL
CSE-844
CSP-844
CSE-948
CSP-948
CSE-1044
CSP-1044
CSE-1054
CSP-1054
CSE-1248
CSP-1248
CSE-1354
CSP-1354
CSEC-835
CSPC-835
CSEC-1035
CSPC-1035
Rated Softener
Capacity:*
(Grains/Lbs. Salt)
Minimum
13,700 @ 3.4
18,200 @ 4.5
18,200 @ 4.5
27,600 @ 7.0
36,400 @ 9.0
45,800 @ 11.5
5,100 @ 2.3
18,200 @ 4.5
Medium
16,800 @ 6.0
23,500 @ 9.0
23,500 @ 9.0
36,700 @ 15.0
47,000 @ 18.0
53,900 @ 18.0
7,300 @ 6.0
23,500 @ 9.0
Maximum
18,800 @ 8.0
28,000 @ 15.0
28,000 @ 15.0
42,000 @ 22.5
56,100 @ 30.0
69,800 @ 37.0
7,800 @ 7.5
28,000 @ 15.0
Amount of High Capacity Cat-ion Resin (Cu. Ft.)
.75
1.0
1.0
1.5
2.0
2.5
.50
1.0
Efficiency at 1 lb Salt Setting (Grains/Lbs Salt)
4,040/1
4,040/1
4,040/1
4,040/1
4,040/1
4,040/1
N/A
4,040/1
Max. Service Flow Rate (GPM)
11.7
13.1
16.0
13.3
16.4
17.1
9.6
16.0
Max. Pressure Loss at Max. Service (PSI)
15.0
15.0
15.0
15.0
15.0
15.0
9.0
15.0
Min. to Max. Working Pressure (PSI)
30-100
30-100
30-100
30-100
30-100
30-100
30-100
30-100
Min. to Max. Operating Temperature (ºF)
33-100
33-100
33-100
33-100
33-100
33-100
33-100
33-100
Max. Flow to Drain During Regeneration (GPM)
1.3
1.7
2.2
2.2
3.2
3.2
1.3
2.2
Electrical Requirements (volts-hertz)
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
Pipe Size
1”
1”
1”
1”
1”
1”
1”
1”
Total Dimensions:
Media Tank and Valve
8”W x 52”H
9”W x 56”H
10”W x 52”H
10”W x 62”H
12”W x 56”H
13”W x 62”H
14"W x 44.5"H x
20.5"D
14”W x 44.5”H x
20.5”D
Brine Tank
18”W x 33”H
18”W x 33”H
18”W x 33”H
18”W x 33”H
18”W x 40”H
18”W x 40”H
MODEL
CSERC-1054
CSPRC-1054
CSERC-1354
CSPRC-1354
1
Capacity:
(Grains/Lbs. NaCI)
Minimum
23,600 @ 6.0
35,400 @ 9.0
Medium
28,400 @ 9.0
44,400 @ 15.0
Maximum
32,000 @ 15.0
48,800 @ 21.0
Amount of Resin Media (Cu. Ft.)
1.0
1.5
Amount of Carbon Media (Cu. Ft.)
.5
1.0
Maximum Water Hardness (GPG)
75
100
2
Maximum Iron (PPM)
1.0
1.0
3
Peak Flow Rate (GPM @ P-PSI)
15.6 @ 15.0
20.4 @ 15.0
Service Flow Rate (GPM @ P-PSI)
9.7 @ 7.5
13.2 @ 7.5
Water Pressure Range (PSI)
25-100
25-100
Water Temp. (ºF)
33-100
33-100
Electrical Requirements (volts-hertz)
110-50/60
110-50/60
Pipe Size
1”
1”
Total Dimensions:
Media Tank and Valve
10”W x 62”H
13”W x 62”H
Brine Tank
18”W x 33”H
18”W x 40”H
*CSERC/CSPRC Specifications
CSE/CSEC/CSP/CSPC Specifications
MODEL
CSE-844
CSP-844
CSE-948
CSP-844
CSE-1044
CSP-1044
CSE-1054
CSP-1054
CSE-1248
CSP-1248
CSE-1354
CSP-1354
CSEC-835
CSPC-835
CSEC-1035
CSPC-1035
CSERC-1054
CSPRC-1054
CSERC-1354
CSPRC-1354
Brine Refill
2
3
3
4.5
6
7.5
1.5
3
6
10
Regenerant (lbs)
3.4
4.5
4.5
7.0
9.0
11.5
2.3
4.5
9
15
Service
240
240
240
240
240
240
240
240
240
240
The above sequence takes place prior to regeneration; therefore, minutes are not included in totals.
Backwash
6
8
8
8
10
10
6
8
8
8
Brine and Rinse
40
60
60
90
90
90
40
60
90
90
Rinse
4
4
4
4
4
4
4
4
4
4
Total
50
72
72
102
104
104
50
72
102
102
Width
Height
Depth
Low Profi le Cabinet
High Profi le Cabinet
Width
Height
Cabinet Models
Manufacturer recommends the use of coarse solar salt in these water softeners.
CSE and CSP -844, -948, -1044, -1054, -1248, -1354 and CSEC and CSPC -835, -1035 softeners are certified by WQA against NSF/ANSI Standard 44 for the reduction of
hardness as verified and substantiated by test data.
Only the efficiency-rated water softener models have a rated capacity of not less than 3,350 grains of total hardness exchange per pound of salt (based on NaCl) and
shall not deliver more salt or be operated at a sustained maximum service flow rate greater than its listed rating. Efficiency is measured by a laboratory test described
in NSF/ANSI 44. The test represents the maximum possible efficiency the system can achieve after the system has been installed. The operational efficiency is typically
less than the efficiency due to individual application factors including water hardness, water usage, and other contaminants that reduce the softener’s capacity.
These water softeners are not intended to be used for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or
after the system.
SPECIFICATIONS
