background image

A.  DETERMINE THE APPLIANCE LOCATIONS

 

The appliance can be located under a sink or in a base-

ment depending on space availability and the customer’s 
preference.  If a basement installation is selected, additional 
tubing, hardware and fittings may be needed and a hole will 
have to be made from inside the cabinet, through the floor, to 
the basement.  

Never install it in an area of the home where 

the temperature may drop below 40

°

C, because damage to the 

appliance may occur.
 

The exact placement of the various components of the 

appliance will vary from installation to installation.  The install-
er, in conjunction with the customer, must decide on where to 
place the faucet, tank and filtration assembly by balancing the 
homeowner’s convenience with ease of installation and servic-
ing.  (See Fig. 1 & 7)
 

Considerations for an icemaker or other remote hookup 

should be predetermined, including routing and any additional 
tools, fittings, and tubing that may be required.

B.  PREPARE THE AREA FOR INSTALLATION

 

Re move supplies from under the sink and stack them 

neatly away from the working area. Ar range a light for the work 
area, if necessary.
 

If a basement installation is called for, determine where 

the components will be located and how they will be mounted. 
Special mounting brackets and hardware may be necessary to 
secure the appliance to a wall or ceiling joists. (See Figure 7)
 

Inspect the cold water supply line and determine if any 

special fittings, in addition to what is included in the kit, are 
required.
NOTE:  It is a good idea at this time to check the condition of 
the undercounter plumbing for any existing or potential leaks.  
Make sure to perform any necessary repairs prior to the instal-
lation of the drinking water device.

I. Installation Instructions

3

Fig. 1

Drain

Saddle

Sink Drain

Storage Tank

Filtration System

1/4" Orange

Tubing

3/8" Yellow

Tubing

Pressure Relief Valve

(required, not included)

Storage Tank Valve

Red SFC Tubing

1/4" Green

Tubing

Feedwater

Connection

Placement

3/8" Blue

Tubing

3/8" Black

Tubing

Reducing

Union

Summary of Contents for SQC3 Series





















Reviews: