Water Right ASP-TW, Installation Instructions & Owner'S Manual

30

31

MANUAL REGENERATION

NOTE:

 For softeners, if brine tank does 

not contain salt, fill with salt and wait at 

least two hours before regeneration. If 

you need to initiate a manual regeneration 

immediately, press and hold 

�����

 until 

valve motor starts (typically 3 seconds). 

ERROR

If the display toggles between “Error” and 

an error code (i.e. a number), call a service 

technician and report the error code.

BYPASS VALVE OPERATION

To shut off water to the system, position arrow handles as shown in the bypass 

operation diagram below. If your valve doesn’t look like the diagram below, contact 

your service technician for instructions on how to shut off water.

REGEN TODAY

MON

GPM

2:40

8

PM

REGEN TODAY 

and 

TIME OF DAY 

will flash alternately if a regeneration 

is expected tonight.

ERROR 

106

CALL FOR SERVICE

QUICK REFERENCE GUIDE

GENERAL OPERATION

When the system is operating, one of five displays will be shown:

1. Time of day/gpm   

4. Days to a regen

2. Flow rate 

5. Dealer name and phone number

3. Capacity remaining

Pressing 

����

 will toggle between the five choices.

TO SET TIME OF DAY

In the event of a prolonged power outage, time of day flashes, indicating 

that this needs to be reset. All other information will be stored in memory 

no matter how long the power outage.

1.  Accessed by pressing 

�����

2.  Adjust hours with 

+

 and 

—

 buttons, AM/PM toggles at 12

3. Press 

����

4.  Adjust minutes with 

+

 and 

—

 buttons

5. Press 

����

6. Adjust current day with 

+

 and 

—

 buttons

7.   Press 

����

 to complete and return to normal operation

DAYS TO A REGEN

GPM

3

A

FLOW RATE

GPM

8.0

TIME OF DAY

MON

GPM

2:40

A

PM

PHONE NUMBER

DEALER NA

A

CAPACITY REMAINING

GAL

1600

A

CURRENT DAY

SET

MON

TIME

MINUTES

SET

TIME

HOUR

SET

2:00

AM

2:00

AM

ADJUST HARDNESS, DAYS BETWEEN REGENERATION, 
TIME OF REGENERATION AND ALARM BUZZER

For initial set-up or to make adjustments, please complete the following steps.

1.  Accessed by pressing 

����

 and 

+

 button 

simultaneously

2.  Adjust hardness using 

+

 and 

—

 buttons

3. Press 

����

4.  Adjust days between regenerations

or number of times per day using

+

 and 

—

 buttons

5. Press 

����

6.  Manufacturer has set 

regeneration to occur when 

zero gallons remain.

7. Press 

����

8.  Turn service alarm by gallons 

ON with 

+

 and 

—

 buttons. 

Default is OFF.

9. Press 

����

10.  Turn service alarm by time ON 

with 

+

 and 

—

 buttons. Default 

is OFF.

11. Press 

���� 

three times

12.  Turn alarm buzzer ON

or OFF with 

+

 and 

—

 buttons.

13. Press 

����

14.  Adjust alarm buzzer start time 

with 

+

 and 

—

 buttons.

15. Press 

����

16.  Adjust alarm buzzer end time 

with 

+

 and 

—

 buttons.

17. Press 

����

18.  Turn display backlight ON or OFF

with 

+

 and 

—

 buttons. Default is ON. 

19.   Press 

����

 to complete and

return to normal operation.

“TREATED”

WATER EXITS

SUPPLY

WATER ENTERS

SUPPLY

WATER EXITS

SUPPLY

WATER ENTERS

NORMAL OPERATION

BYPASS OPERATION

ALARM BUZZER START

SET

6:00

AM

ALARM BUZZER END

SET

10:00

PM

SERVICE ALARM

SET

OFF

DAYS BETWEEN REGEN

SET

OFF

WATER HARDNESS

SET

20

GR

LIGHT NORMALLY

SET

ON

SERVICE ALARM

SET

OFF

REGEN IMMEDIATE

ON ZERO

GAL

GAL

YR

ALARM BUZZER

SET

ON

Return to 
General Display