Water Right ASP-TW, Installation Instructions & Owner'S Manual

6

7

PROGRAMMING PROCEDURES

Typically, time of day should only need to be set after extended power outages or when daylight saving time begins or ends or after the battery has 

been replaced. If an extended power outage occurs, the time of day will flash on and off indicating that the time should be reset. To set the clock:

STEP 1 –

 Press the 

CLOCK

 button.

STEP 2 –

  Set the hour of the day using 

+

 or 

–

 buttons. AM/PM toggles after 12. Press 

NEXT 

to go to step 3.

STEP 3 –

   Set the minutes using 

+

 or 

–

 buttons. Press 

NEXT

 to go to step 4 or 

REGEN

 to return to previous step. 

STEP 4 –

  Set the day of the week using 

+

 or 

–

 buttons. Press 

NEXT

 to exit clock setting or 

REGEN

 to return to previous step. 

1

TIME

HOUR

AM

SET

2:00

TIME

MINUTES

AM

SET

2:00

2

3

CURRENT DAY

SET

MON

4

return to general display

TIME OF DAY

MON

PM

GPM

2:40

8

1 . Set Time of Day

2 . Programming

1

DAYS BETWEEN REGEN

SET

 OFF

3

WATER HARDNESS

SET

20

2

REGEN IMMEDIATE

GAL

GR

ON ZERO

4

Return to general display.

LIGHT NORMALLY

SET

ON

6

ALARM BUZZER

SET

ON

5

The manufacturer has preset the unit so that the gallons between regenerations will be automatically calculated 

after the hardness is entered. Press 

NEXT

 to cycle to the next step or 

REGEN

 to return to the previous step. 

STEP 1

 – Press and hold the 

NEXT

 and 

+

 buttons simultaneously for 3 seconds.

STEP 2

 –  

HARDNESS: 

Use the 

+

 or 

–

 buttons to adjust the hardness value in grains per gallons. Adjustable 

from 1 to 150 gpg in 1 grain increments (default setting is 20).

The hardness value is based on the actual compensated hardness of the water and must be set by 

an authorized dealer following an on-site water analysis. Adjusting the number will only impact the 

frequency of regeneration and will not alter or affect the hardness of the water treated by the unit. 

Note: If a resin media is used, increase the grains per gallon if soluble iron is present 

(1 ppm = 4 gpg). This screen will not display if “FILTER” mode is selected. 

STEP 3

 – 

DAYS BETWEEN REGENERATION (DAY OVERRIDE): 

Use the 

+

 or 

–

 buttons to adjust the day override. 

Adjustable from 1-28 days or OFF. The manufacturer has factory set OFF as the default for Twin units.
The Day Override value represents the maximum number of days between regenerations. If any number 

is set (1-28 days), a regeneration will be scheduled for that day if the gallon capacity has not been met.  If 

OFF is set, the unit will only initiate a regeneration once the gallon capacity has been met. 

STEP 4

 – 

IMMEDIATE REGENERATION:

The manufacturer has set the regeneration to occur when zero gallons 

remain. When this occurs, the standby tank will switch into service and provide treated water while the 

tank requiring regeneration will start this process. 

STEP 5

 – 

 ALARM  BUZZER

 (only available on Conditioner models)

:

Use the 

+

 or 

–

 buttons to turn the alarm ON 

or OFF. Unit is set to ON by default. Alarm will sound immediately if there is no salt detected in the brine 

tank or if an error has occurred.

STEP 6

 – 

 BACKLIGHT DISPLAY CONTROL: 

Use the 

+

 or 

–

 buttons to turn the backlight setting ON or OFF. If unit is 

set to OFF, the backlight will turn off after 5 minutes of inactivity. 

Press 

NEXT

 to return to General Display.

Note: To alternate between tanks without activating a regeneration, press and hold 

CLOCK

 and 

+

 buttons 

simultaneously for three seconds.