32
SANITIZER
®
PLUS TWIN SPECIFICATIONS
*All specs are shown in capacity per tank.
NOTE:
Only the -844TW through the -1354TW sizes are approved in the state of Wisconsin.
1
All Sanitizer Plus Twin water conditioners are pre-factory set at medium salting.
NOTE:
Influent waters must be at least 3 GPG hardness and 80 TDS. A calcite or corsex unite may be needed for
correct operation.
2
Combined iron and managnese removal varies depending on the form of iron, manganese, pH and other local conditions. On waters
that are pre-chlorinated or where other pre-oxidation occurs, precipitated metal oxides may form that are too fine to be filtered.
3
The pH listed is the minimum for influent water.
4
Optimum pH adjustment occurs at 3.0 gpm or less at maximum salt settings. Higher flow rates will produce less pH adjusted water.
5
Unit not tested for capacity at these flow rates. Water quality may vary.
Twin Series Conditioners
Specifications
Manufactured by Water-Right, Inc. • 1900 Prospect Court • Appleton, WI 54914 • 800-777-1426 • water-right.com
SPE-SAN PL TWIN RevA0318
CYCLE TIMES AND USAGE
ASP1 SPECIFICATIONS
ASP2 SPECIFICATIONS
MODEL
ASP1-1044TW
ASP1-1054TW
ASP1-1354TW
ASP1-1465TW
ASP1-1665TW
1
Capacity:*
(Grains/Lbs. NaCl)
Minimum
7,300 @ 3.2
16,400 @ 6.1
28,300 @ 9.5
40,000 @ 13.0
51,000@ 17.0
Medium
11,400 @ 9.3
20,700 @ 12.4
33,600 @ 15.9
47,000 @ 22.0
60,000 @ 29.0
Maximum
11,800 @ 12.4
22,600 @ 15.9
36,900 @ 21.2
52,000 @ 30.0
51,000 @ 17.0
Amount of Media (Cu.Ft.)
1.0
1.5
2.5
3.5
4.5
Maximum Water Hardness (GPG)
20
30
40
40
40
2
Maximum Iron and Manganese (PPM)
8.0
10.0
15.0
15.0
15.0
3
Minimum pH
6.5
6.0
6.0
6.0
6.0
4
Total pH Adjusted Water
510
510
863
N/A
N/A
5
Peak Flow Rate (GPM @ P-PSI)
19.0 @ 8.3
17.0 @ 7.8
19.0 @ 7.6
26.0 @ 25.0
26.0 @ 25.0
Continuous Flow Rate (GPM @ P-PSI)
9.0 @ 2.4
9.0 @ 2.8
9.0 @ 2.7
19.0 @ 15.0
19.0 @ 15.0
Water Pressure Range (PSI)
25-100
25-100
25-100
25-100
25-100
Water Temp. (ºF)
33-100
33-100
33-100
33-100
33-100
Electrical Requirements (volts-hertz)
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
Pipe Size
1”
1”
1”
1”
1”
Total Dimensions:
Media Tank
10”W x 52”H
10”W x 62”H
13”W x 62”H
14”W x 65”H
16”W x 65”H
Brine Tank
18”W x 33”H
18”W x 33”H
18”W x 40”H
18”W x 40”H
24”W x 41”H
MODEL
ASP2-1044TW
ASP2-1054TW
ASP2-1354TW
ASP2-1465TW
ASP2-1665TW
1
Capacity:*
(Grains/Lbs. NaCl)
Minimum
11,100 @ 3.2
22,900 @ 6.1
28,200 @ 9.3
40,000 @ 13.0
52,000 @ 17.0
Medium
19,100 @ 9.3
32,000 @ 12.4
48,300 @ 15.9
68,000 @ 22.0
87,000 @ 29.0
Maximum
20,300 @ 12.4
34,800 @ 15.9
60,300 @ 26.5
84,000 @ 37.0
108,000 @ 48.0
Amount of Media (Cu.Ft.)
1.0
1.5
2.5
3.5
4.5
Maximum Water Hardness (GPG)
40
60
80
80
80
2
Maximum Iron and Manganese (PPM)
8.0
10.0
15.0
15.0
15.0
3
Minimum pH
7.0
7.0
7.0
7.0
7.0
4
Total pH Adjusted Water
N/A
N/A
N/A
N/A
N/A
5
Peak Flow Rate (GPM @ P-PSI)
19.0 @ 9.3
17.0 @ 9.1
19.0 @ 8.6
26.0 @ 25.0
26.0 @ 25.0
Continuous Flow Rate (GPM @ P-PSI)
9.0 @ 3.0
8.0 @ 3.7
9.0 @ 2.8
19.0 @ 15.0
19.0 @ 15.0
Water Pressure Range (PSI)
25-100
25-100
25-100
25-100
25-100
Water Temp. (ºF)
33-100
33-100
33-100
33-100
33-100
Electrical Requirements (volts-hertz)
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
Pipe Size
1”
1”
1”
1”
1”
Total Dimensions:
Media Tank
10”W x 52”H
10”W x 62”H
13”W x 62”H
14”W x 65”H
16”W x 65”H
Brine Tank
18”W x 33”H
18”W x 33”H
18”W x 40”H
18”W x 40”H
24”W x 41”H
MODEL
ASP1-1044
ASP2-1044
ASP1-1054
ASP2-1054
ASP1-1354
ASP2-1354
ASP1-1465
ASP2-1465
ASP1-1665
ASP2-1665
MIN.
GAL.
MIN.
GAL.
MIN.
GAL.
MIN.
GAL.
MIN.
GAL.
Brine Refill
5:51
3
9:53
5
11:53
6
23:00
11.5
30:00
15
Backwash
12
42
12
48
12
90
12
36
12
108
Brine & Rinse
72
29
90
36
90
50
90
72
90
90
Rapid Rinse
4
14
4
16
4
30
4
30
4
36
Total
94
88
116
105
118
176
129
203.5
136
249
Summary of Contents for Impression Plus IMP-1044TW
Page 22: ...22 REPLACEMENT PARTS...
