COMMON QUESTIONS
Q: The ON-OFF knob has become difficult to turn. What can I do?
A: Clean off the O-rings and add silicone lubricant/sealant. This will ensure easier turning and a
better water tight seal. Refer to the maintenance section for more information.
Q: Can my Pool Blaster be run out of water?
A: Yes, for a short period of time when you turn it on before submering into your pool or spa.
Q: When I am cleaning my pool how do I know when the Pool Blaster is out
of battery power?
A: Most people can feel the Pool Blaster is running through vibration in the vacuum pole or handle.
To be sure you can lift it out of the water to hear if it is running or not.
Q: How often should I clean out my Pool Blaster filter bag?
A: You can clean your filter bag as often as you like with no ill effects. The filter bag can
then be turned inside out and rinsed with a hose or in a sink. Do not wash it in a washing
machine or with detergent. For more detailed instructions, see “Cleaning Your Pool Blaster”
instructions in this manual.
For best results, do this after each use, or whenever you notice the performance of your Pool
Blaster declining.
Q: Is it normal for me to hear air escaping out of the Pool Blaster when I
open the On-Off knob?
A: Yes, the powerful motors heat the air in the motor box, which then expands, creating the air
sound
.
Q: How can I stop dirt from coming out of the nozzle when I take the
cleaner out of the water?
A: There are two ways to remove the unit from the pool when done cleaning:
WHEN USING HANDLE: Lift from pool with the nose facing up to allow the water to escape
from the back and sides.
WHEN USING A VACUUM POLE: Remove the unit from the pool with the bottom facing up-
wards and the handle facing down. This will allow the water to escape and keep the dirt inside.
Q: How can I Prevent sand and silt from escaping through the filter bag?
A: The Pool Blaster comes standard with an all-purpose filter bag. A Sand and Silt bag (Part No.
PBW022SS) is available. To purchase contact your retailer or call us at 1-800-298-8800.
Q: What if I put the Pool Blaster in the pool without the On-Off Knob in
place?
A: Do not operate your Pool Blaster if water gets inside the machine. Put the Pool Blaster on its
side to drain the water out of the knob hole and tilt side to side to get the water out. Do not use
for at least 24 hours. If possible, you can speed the drying process with a blow dryer. To avoid
serious injury or damage, do not replace the knob or attempt to charge or operate your Pool
Blaster until it is completely dry.
Q: Can I leave my Pool Blaster on the charger all the time?
A: After charging is complete, the Pool Blaster and charger should be removed from the outlet.
This will prevent overcharging and prolong the life of your battery pack. IMPORTANT: Discon-
nect the charger before storing your Pool Blaster.
Q: Can I replace the batteries myself?
A: Under no circumstances should you attempt to open the motor housing or battery housing. The
batteries and motor are factory installed and sealed, and your rechargeable battery should give
you many hours of use. If your motor, batteries, or charger stop working, take the Pool Blaster to
an authorized service center.
Q: Where can I buy replacement parts?
A: Look for original Water Tech replacement parts at your local retailer or call 1-800-298-8800 for
more details.
Q: Will my pool chemicals hurt the Pool Blaster?
A: The Pool Blaster is designed to withstand pool chemicals during its usage period. However, it
should be rinsed off with fresh water after it is removed from the pool. This will increase the life
of the filter bag/seal ring
.
Q: Can I leave the Pool Blaster in the pool when not in use?
A: No. The Pool Blaster should be removed from the pool and stored in a clean, dry place when
not in use. This will increase the life of your Pool Blaster and its accessories
.
Q: What do I do if my Pool Blaster does not vacuum?
A: Make sure your Pool Blaster is completely submerged in the water and the air is out of the clear
funnel. The cleaner is only designed to vacuum water and will not vacuum air.
If that does not resolve your situation please check the following:
• Make sure the filter bag is clear of debris that may be obstructing the flow.
• Make sure the Pool Blaster is in the 12 o’clock “ON” position.
• Charge your Pool Blaster for at least 24 hours.
If none of the above help resolve the situation,
please call our Customer Service Division at 1-800-298-8800.
