ITEM No. DESCRIPTION
PART No.
QTY.
1
Vacuum Head (Home PRO/PRO)
PROA006
1
2
Vacuum Head Brushes (Home PRO/PRO)
PROW049
6
3
Vacuum Head Wheels (Home PRO/PRO)
PROW050 11
4
Vacuum Head (PRO 1500)
PROA201
1
5
Universal Vac Head Adaptor (PRO/PRO 1500) PROA200
1
6
Nose Cap
PROA002
1
7
All Purpose Filter Bag/Seal Ring
PROW022AP
1
8
Pool Blaster PRO
PROA005
1
9
Battery Charger
PROA099*
1
10
Spring Clip
PROW041
1
11
Battery Pack
PROA007
1
12
Motor Box Cap
PROA060
1
13
Sand and Silt Bag (not shown)
PROW022SS 1
14
Multi Layer Microfilter Bag (not shown)
PROWO22MF
1
15
Shoulder Strap
PROW070
1
ADDITIONAL PARTS AVAILABLE:
Shallow Water Hose Attachment (part No. PROASHA)
* U.S. Charger (part No. PROA099)
* European 230V Charger (part No. PROA099EU)
To purchase, contact your retailer or call us at (800)298-8800
WARNING:
The Battery Charger is for indoor use only.
WARNING:
Do not expose charger to excessive moisture or extreme heat or cold. Charge battery only with the battery charger provided.
CHARGING BATTERIES
BATTERY LIFE
•
Your battery pack should give you many hours of use. If your motor, batteries, or charger stop working, take the cleaner to an authorized service center.
• NEVER leave your battery plugged in for long term storage.
• The Battery Pack should be charged at least once a month when not in regular use.
5
6
7
8
9
15
11
The battery pack for your cleaner has been shipped in a low voltage
condition. It should be charged for 12 Hours prior to initial use.
1. Remove the battery pack from the rear of the cleaner.
2. Attach the Battery to the Battery Charger.
3. Plug the Battery Charger to any standard 115V/60Hz electrical outlet. The L.E.D. on the charger
will glow red. When the battery is fully charged the L.E.D. will turn Green.
When the charge has been exhausted, recharge the battery for 10 - 12 Hours.
10
12
1 3
Important Tips:
•
Store your cleaner in a clean, dry place when not in use. Do not leave it underwater, in direct sunlight, or exposed to extreme heat or
cold.
•
You may clean the cleaner body with soap and water. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to
damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease
etc.
•
The Motor Box Gasket should be periodically lubricated with a silicon-based grease
•
General maintenance of your cleaner requires you occasionally clean off the gasket on the Motor Box Cap and add silicone lubricant/seal
-
ant. This will ensure a water-tight seal. This lubricant is available at your local pool & spa retailer.
•
In the Nose Cap (Part No. PROA002) there is a Flapper Valve. To keep the Nose Cap Flapper Valve moving freely, clean the valve after
every use. This will help to keep dirt inside the cleaner after the cleaner is removed from the pool.
CAUTION:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts.
They contain chemicals that can damage, weaken, or destroy plastic.
WARNING:
Do not attempt to modify this tool or create accessories not approved for use with this tool. Any such alteration or modification
is misuse and could result in a hazardous condition leading to possible serious injury. Do not attempt in any way to destroy or disassemble motor
box or any of its components. Instead, take your cleaner to an authorized service center. Failure to follow these instructions may void your warranty
agreement.
Service Information
NOTE:
Any repairs requiring disassembly must be performed by a Water Tech Authorized Service Center. For the repair center nearest you call us
toll free at 1-800-298-8800. Unauthorized repairs will void the warranty.
Storing the Cleaner
NOTE: State of the art Nickel-Metal Hydride batteries power the cleaner. In order to properly ventilate and cool the batteries and drive system a
certain amount of space is left open in the cleaner body. As a result, from time to time, water may enter the unit. In order to allow for any water to be
drained you should remove the Motor Box Cap after each use, turn the machine on end so the opening is towards the floor and tilt side to side in all
directions. The amount of water may be very small or not noticed at all. Water entering the cleaner body presents no safety hazard and should be
drained to avoid any chance of long-term corrosion. The batteries and motor in the cleaner are long lasting and proper care will help to prolong the
life of your cleaner.
NOTE:
Remove Battery Pack from the charger before storage.
When not in use, your cleaner should be stored indoors, in a clean dry location sheltered from direct sunlight, extreme temperatures and rain. Do
not store the cleaner in a garage or anywhere the unit could freeze. Storing the cleaner in areas of high humidity can affect battery performance over
time.
Long Term Storage
Follow the above storage instructions and unplug the charger from the electrical outlet. Whenever you do not use you Pool Blaster PRO for an
extended period of time, the battery/batteries should be charged once a month for a 12 hour period.
When charging for the first time after long-term storage, your cleaner may take 2-3 uses before full time is achieved.
Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including inter-
ference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try and correct the interference by one or more of the following measures:
- Reorient or relocated the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different than that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
4
Meijer.com
