background image

 

01/2015 

 

 

 

BB-4-18/23 Quick Guide 

This Quick Guide shows the basic operation of the 

WATERAX

 BB-4-18/23 4-stage high pressure pump.  

 

The 

WATERAX

 BB-4 pump model pairs a 

WATERAX

 4-

stage pump end with a Briggs & Stratton Vanguard 18 
HP or 23 HP gasoline engine. For engine instructions, 
oil and fuel recommendations, please refer to the engine 
manufacturer’s manual. 

 

For detailed instructions on using and troubleshooting 
your pump, as well as full service and maintenance 
instructions, refer to our website to download the 

BB-4 

Owner’s Manual

.  

 

For full specifications and performance curves, see the 
BB-4-18 or BB-4-23 Data Sheets. 

 

Warnings and Safety Precautions

 

This  warning  label  appears  on  all 

WATERAX

  pumps  to  identify  safety 

hazards as follows: 

 

READ YOUR ENGINE MANUAL!   

 

Before proceeding further, locate and read the engine 
manufacturer’s manual. It contains very important safety 
information that 

MUST

 be read, understood and followed to 

safeguard you and your equipment from harm, as well as for 
the proper use and care of your engine. Use only fuel and oil 
type recommended in the engine manufacturer’s manual. 
Always check oil level in crankcase before use.  

WEAR EAR AND EYE PROTECTION.   

 

Always wear eye and ear protection when operating the 
pump unit. Sound level of the unit: 99 dB(A). 

GENERAL WARNINGS: 

 

 

Do not operate if mentally/physically fatigued. 

 

Inspect hoses and piping to avoid burst injuries. 

 

No modifications and/or alterations may be made to the 
pump. Any such modifications void the pump warranty 
and can endanger pump operators. 

 

Do not operate the pump above the maximum rated 
pressure. Use only pipe, hose, and fittings rated at or 
above the maximum pressure rating of the pump or 
system design.  

 

Slowly close valves. Use slow close valves wherever 
possible to safeguard operators and prevent damage 
from water hammer. 

 

Dry weight of the unit: 164 lbs (will vary depending on 
options). 

READ THE PUMP OWNER’S MANUAL! 

 

The improper use of this pump could result in serious injuries 
as well as damage to the unit. Read the 

BB-

4 Owner’s 

Manual

 before using your BB-4 pump unit and follow the 

safety instructions in this Quick Guide.  

NEVER RUN THE ENGINE IN A CLOSED 
OR CONFINED AREA

.

 Exhaust gas contains 

carbon monoxide which is poisonous to humans. 
Avoid inhalation of exhaust gas.

  

REFUEL ENGINE WITH CARE

. Gasoline is 

extremely flammable, and gasoline vapor can 
explode. Refuel in a well-ventilated area, with the 
engine stopped. 

NEVER TOUCH ANY EXHAUST SYSTEM 
PARTS WHILE ENGINE IS RUNNING

. Always 

allow enough time, after stopping the unit, for proper 
cooling of the muffler and surrounding parts.  

EQUIPMENT DAMAGE PREVENTION: 

 

Flush the pump with fresh water if the pump has been 
used to pump salty, brackish, high mineral content 
water, water containing debris, or foam injected water. 
Check that debris is cleared before using the pump 
again. 

 

Always draft water using a suction hose strainer. 

Summary of Contents for BB-4-18/23

Page 1: ...tigued Inspect hoses and piping to avoid burst injuries No modifications and or alterations may be made to the pump Any such modifications void the pump warranty and can endanger pump operators Do not operate the pump above the maximum rated pressure Use only pipe hose and fittings rated at or above the maximum pressure rating of the pump or system design Slowly close valves Use slow close valves ...

Page 2: ... manual Priming Port Suction Intake Port Discharge Port 2 Connect the suction hose using a universal hose coupling wrench to tighten coupling firmly Drafting Mode Connect footvalve strainer to male end of suction hose then fill suction hose with water and connect to pump intake Flooded Suction Mode Connect female end of suction hose to pump intake and connect male end to hydrant or other supply a ...

Page 3: ...trol Panel is on the ON position Give starter rope a quick steady pull until engine starts f Open disengage choke g Allow the engine to warm up for at least 2 minutes before using full throttle Throttle Start Button On Off toggle switch Engine Mount Control Panel optional 6 Engage the exhaust primer a Open priming valve located just below check valve on portable units b Adjust THROTTLE to full spe...

Page 4: ...all valves and plug all openings g Follow any other product component apparatus and departmental procedures and or guidelines before placing the unit in storage Make sure all necessary tools spares and accessories are with the pump To operate the BB 4 18 23 unit in cold weather The pump can be run in below freezing temperatures if certain precautions are taken to avoid the formation of ice in the ...

Reviews: