26
PERFORMANCE DATA SHEET:
MODEL
CSP- 844 CSP- 948
CSP-1044
CSP-1054
CSP-1248
CSP-1354
Minimum
13,000 @ 3.4
18,000 @ 4.5
18,000 @ 4.5
27,500 @ 7.0
36,000 @ 9.0
45,000 @ 11.5
Medium
16,500 @ 6.0
23,000 @ 9.0
23,000 @ 9.0
36,000 @ 15.0
46,000 @ 18.0
53,000 @ 18.0
Maximum
18,500 @ 8.0
28,000 @ 15.0
28,000 @ 15.0
42,000 @ 22.5
56,000 @ 30.0
69,000 @ 37.0
Efficiency at 1 lb Salt Setting (Grains/Lbs Salt)
4,042/1
4,042/1
4,042/1
4,042/1
4,042/1
4,042/1
Max. Service Flow Rate (GPG)
11.7
13.1
16.0
13.3
16.4
17.1
Max. Pressure Loss at Max. Service (PSI)
15
15
15
15
15
15
Min. to Max. Working Pressure (PSI)
30-100
30-100
30-100
30-100
30-100
30-100
Min. to Max. Operating Temperature (ºF)
33-100
33-100
33-100
33-100
33-100
33-100
Max. Flow to Drain During Regeneration (GPM)
1.3
1.7
2.2
2.2
3.2
3.2
Amount of High Capacity Cat-ion Resin (Cu. Ft.)
.75
1.0
1.0
1.5
2.0
2.5
Electrical Requirements (volts-hertz)
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
110-50/60
Pipe Size
1"
1"
1"
1"
1"
1"
Total Dimensions:
Media Tank and Valve
8"W x 52"H
9"W x 56"H
10"W x 52"H
10"W x 62"H
12"W x 56"H
13"W x 62"H
Brine Tank
18"W x 33"H
18"W x 33"H
18"W x 33"H
18"W x 33"H
18"W x 40"H
18"W x 40"H
Rated Softener
Capacity:*
(Grains/Lbs. Salt)
*All CareSoft Pro water softeners are set at “minimum salting” from the factory.
MODEL
CSPC - 835 CSPC - 935
CSPC -1035
Minimum
7,000 @ 2.3
10,500 @ 3.4
18,000 @ 4.5
Medium
10,000 @ 6.0
13,000 @ 6.0
23,000 @ 9.0
Maximum
10,500 @ 7.5
16,000 @ 11.0
28,000 @ 15.0
Efficiency at 1 lb Salt Setting (Grains/Lbs Salt)
4,042/1
4,042/1
4,042/1
Max. Service Flow Rate (GPG)
9.6
14.4
16.0
Max. Pressure Loss at Max. Service (PSI)
8.6
14.1
15.0
Min. to Max. Working Pressure (PSI)
30-100
30-100
30-100
Min. to Max. Operating Temperature (ºF)
33-100
33-100
33-100
Max. Flow to Drain During Regeneration (GPM)
1.3
1.7
2.2
Amount of High Capacity Cat-ion Resin (Cu. Ft.)
.50
.75
1.0
Electrical Requirements (volts-hertz)
110-50/60
110-50/60
110-50/60
Pipe Size
1"
1"
1"
Total Dimensions:
Media Tank
13.5"W x 42.5"H x
13.5"W x 42.5"H x
13.5"W x 42.5"H x
22.5"D
22.5"D
22.5"D
Rated Softener
Capacity:*
(Grains/Lbs. Salt)
These softeners conform to NSF/ANSI 44 for the specific performance claims as verified and substantiated by test data. The Demand
Initiated Regeneration (DIR) water softener complies with specific performance specifications intended to minimize the amount of
regenerant brine and water used in its operation. Efficiencies are only valid at stated salt dosages and maximum service flow rate.
These water softeners have a rated capacity of not less than 3,350 grains of total hardness exchange per pound of
salt (based on NaCl) and shall not deliver more salt or be operated at a sustained maximum service flow rate
greater than its listed rating. Efficiency is measured by a laboratory test described in NSF/ANSI 44. The test
represents the maximum possible efficiency the system can achieve after the system has been installed. The
operational efficiency is typically less than the efficiency due to individual application factors including water
hardness, water usage, and other contaminants that reduce the softener’s capacity.
These water softeners are not intended to be used for treating water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system.
CSP Model
CSPC Model
Width
Height
Depth
Height
Width
