background image

WARNING:  USE ONLY CERAMIC GLASS 5mm
THICK.  ABUSE SUCH AS STRIKING, SLAMMING
AND 

USE 

OF 

SUBSTITUTE 

MAT E R I A L S

SHOULD BE AVOIDED.

FIRE SAFETY

To  provide  reasonable  fire  safety,  the  following
should be given serious consideration:

1.

The installation of smoke detectors.

2.

A conveniently located Class A fire extin-
guisher to contend with small fires resulting 
from burning embers.

12

3.

A practiced evacuation plan.

4.

A plan to deal with a chimney fire as follows:

IN THE EVENT OF A CHIMNEY FIRE

(a)

Notify the fire department.

(b)

Prepare occupants for immediate evacuation

(c)

Close all openings into the stove.

(d)

While awaiting fire department watch for igni-
tion to adjacent combustibles from over 
heated stove pipe or hot embers or sparks 
from the chimney.

LEPRECHAUN 90 O.S.A.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS:
SIDE WALL TO STOVE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 INCHES - 510 mm
BACK WALL TO CHIMNEY CONNECTOR .................................18 INCHES - 460mm
BACK WALL TO STOVE TOP & REAR EXIT ..............................14

1/2

” INCHES -  370mm

CEILING TO HORIZONTAL CONNECTOR .................................18 INCHES -  460mm
CORNER. .....................................................................................13 INCHES - 330mm
MANTLE CLEARANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 INCHES - 635mm
SIDE TRIM ...................................................................................14 INCHES - 355mm

FLOOR PROTECTION

When installing this heater on a combustible floor, a floor protector consisting of a layer of non-combustible
material at least 3/8” thick or 1/4” thick covered with 1/8” sheet of metal is required to cover the area under the
heater to extend at least 18” at the front and 8” to the sides and back of stove.  This will provide protection from
sparks and ember which may fall out from the door when stoking or refuelling.

Waterford Stanley Ltd.,

Bilberry, Waterford, Ireland.

Tel:  051-302300

Fax:  051-302375

Rev:  001:   DP030814

Summary of Contents for LEPRECHAUN 90 O.S.A













Reviews: