background image

 

 

 

 

 

 

 

CX Series Centrifugal Fire Pumps 

Operation and Maintenance Instructions 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table of Contents 

 

 

 

 

 

 

 

 
 
 
 
 
 
 

 

 

 

F-1031, Section 2109.1 (Rev: 7/14/20) 

 

 

 

 

 

 

Waterous Company, 125 Hardman Avenue South, South St. Paul, Minnesota  55075  USA  (651) 450-500

www.waterousco.com

 

 

 

NOTE: Instructions subject to change without notice 

 

  

 

 

Read through the operation instruc- 
tions carefully before using your 
Waterous Fire Pump.

 

Safety Information

------------------

----------------------------- 2, 3 

Introduction------------------------------------------------------------- 4 

General Description: 

Components------------------------------------------------------------ 4 

Options---------------------------------------------------------------- 4, 5  

Operating Instructions: 

Pumping from Water Tank------------------------------------------ 6 

Pumping from Hydrant or in Relay-------------------------------- 7 

Pumping from Draft--------------------------------------------------- 8 

Fire Hose Testing----------------------------------------------------- 9 

Maintenance:   

Corrosion Protection------------------------------------------------ 10 

 

Optional Intake Screens------------------------------- 10 

 

Optional Anodes----------------------------------------- 10 

Mechanical Seal------------------------------------------------------ 11 

Packing----------------------------------------------------------------- 11 

 

Packing Removal---------------------------------------------- 11 

 

Packing Installation-------------------------------------------- 12 

 

Packing Adjustment------------------------------------------- 12 

Vacuum Test---------------------------------------------------------- 13 

Overheat Protection Manager (OPM)--------------------------- 13 

Butterfly Valve (BFV)------------------------------------------------ 13 

Summary of Contents for CX Series














Reviews: