For replacement parts, filters, or other well and irrigation accessories, please visit www.watersourceusa.com or call us at 1-800-346-7611
*
This is the filter that comes with your unit
Installation (continued)
7.
Install the filter in the preferred vertical position with flush valve (F) pointing down. However, the filter will work in the
horizontal position if unable to be installed in the vertical position.
Optional: Install a pipe into the bottom of the flush valve (F) so that water and sediment can flow to a drain when cleaning.
(See CLEANING INSTRUCTIONS below)
The filter should be installed where it can be accessed for proper cleaning and maintenance. Unions should be used on
the inlet, outlet, and drain line to allow for easy maintenance. A shut off valve should be installed on the outlet side to
help with maintenance and cleaning.
Install the filter on the pressure side (after discharge) of the pump to allow the filter to be cleaned by flushing collected
sediment through the flush valve. This can be installed before or after the pressure tank and pressure switch. However,
if
being installed before the pressure switch (between pump and pressure tank) be sure to frequently monitor and flush
the Sediment Filter, as a backup of sediment could cause a lower system pressure. A false reading of system pressure
can cause the pump to not shut off and can cause permanent pump damage.
When installing on metallic plumbing, maintain proper electrical grounding. Do not overheat the filter when soldering
copper joints.
Cleaning Instructions – Flushing the Sediment
1.
The primary method of removing sediment from the system is by flushing separated solids through the flush valve while the
filter is under system pressure.
2.
Open the flush valve (F) for 15-30 seconds while system is under pressure from the pump or tank.
3.
For irrigation systems without pressure tanks:
Open the flush valve
Make sure sprinkler valves are turned off
Turn the pump on for 15-30 seconds. This will flush out the filter screen.
4.
The filter screen (C) may need to be removed for cleaning. To remove the filter screen, turn off the water supply, drain
water from the system, unscrew the filter bowl (E), and remove the filter screen (C). Wash off collected sediment from the
screen with warm water. Remove fine particles wedged in the screen by brushing with a soft brush. Apply silicone grease
(DOW 111) to O-rings (B and D) if needed. Reassemble filter screen, bowl, and cap O-ring after cleaning. HAND TIGHTEN
ONLY (Use of tools will void warranty).
Step Down Filtration (Optional)
Step down filtration is recommended when there is heavy sediment found in the water supply. It requires the water to run
through multiple Sediment Filters.
1.
Install a Sediment Filter with a screen that has larger openings (ex. 60 mesh filter) first in line after the pump. This will filter
out large, coarse sediment first, allowing small sediment to pass through.
2.
After installing the first Sediment Filter, install a Sediment Filter with a screen that has smaller openings (ex. 100 mesh filter).
This will filter out small, finer sediment.
For replacement filters, please visit watersourceusa.com or call 1-800-346-7611.
Screen Mesh/ Micron Conversion
Model #
Mesh
Microns
Opening
Example of Sediment
Protects
SFS-30
30
533
.0210 in.
General Usage (Debris), Coarse Sand
General Use, Sprinkler Heads
SFS-40
40
381
.0150 in.
SFS-60
60
254
.0100 in.
Pipe Scale, Medium Sand
Larger Sprinkler Heads, Other Valves
*SFS-100
100
152
.0060 in.
Medium Sand
Domestic Water Use
SFS-150
150
98
.0039 in.
Fine Sand or Grit
Drip Irrigation, Watering devices, Fogger Nozzles
SFS-200
200
74
.0029 in.
SFS-250
250
61
.0024 in.
Very Fine Sand or Grit
Pre-treatment prior to cartridge filters
SFS-500
500
30
.0012 in.
Smaller
Openings
Larger
Openings
NOTE:
To avoid water-hammer, always close the flush valve slowly.
NOTE:
For replacement filters or other components, please visit watersourceusa.com or call 1-800-346-7611.
