background image

Machine Areas

20

Plockmatic PowerSquare™ 224 - Service Training Workbook 

8.3

Gathering Area Module

The gathering area module accepts the paper from the connecting bridge. 
When the correct number of sheets has arrived, tampers knock down the paper 
between the sidelays and the endlays, 

(see Section 8.4)

Locate the following in the Gathering Area (Top)

Bridge Interface PCB (900-278)

Tamper Stepper Motor PCB (900-277)

Main Drive Stepper Motor PCB (900-279)

Bridge Axis Motor Control PCB (900-212)

Gathering Area Loaded Optical Sensor

Gathering Area Flow Optical Sensor

Bridge axis home switch

Main drive proximity sensor

Locate the following in the Gathering Area (Bottom)

Gathering Area cover switch

Bridge axis motor

Main drive stepper motor

Tamper stepper motor

Tamper proximity sensor

Perform the following tasks:

ADJ 4.4.3 (Calibrate the Bridge Axis)

Machine Areas

Plockmatic PowerSquare™ 224 - Service Training Workbook 

29

8.10

Machine Cycle Control

At this stage of the training, you understand how the machine works and how it 
is controlled.

To see the full machine cycle, make a test book using the 

TEST

 screen.

Before you begin:  

• Use the GUI to adjust the PSQ for the correct paper size, book thickness, 

etc.

• Select 2 stitches. 
• Place the paper in the gathering area.

Use the 

TEST

 screen to make a book:  

• Motor Slow
• Pick-up - Shuttle x2
• Activate Rear Tamper x2
• 1st Stitch - Shuttle
• Stitch Wire On x2
• Incr Move - Shuttle
• Stitch Wire Off
• Park - Shuttle
• Fold x3
• Clamp
• Form (number of times depends on thickness of book)
• Clamp
• Eject x2
• Outfeed x2 (to drive the book onto the trim stop)
• Blade x3
• Trim Stop
• Outfeed
• Trim Stop
• Outfeed
• Stack Feed x2
• Motor Slow (to turn off the Motor Slow function)

Summary of Contents for Plockmatic PowerSquare 224





























Reviews: