Watlow EZ-ZONE
®
ST
•
30
•
Chapter 3 Operations Page
Chapter 3: Operations Pages
To go to the Operations Page from the Home Page,
press both the Up
¿
and Down
¯
keys for three sec-
onds.
[``Ai]
will appear in the upper display and
[oPEr]
will appear in the lower display.
• Press the Up
¿
or Down
¯
key to view available
menus. On the following pages top level menus
are identified with a yellow background color.
• Press the Advance Key
‰
to enter the menu of
choice.
• If a submenu exists (more than one instance),
press the Up
¿
or Down
¯
key to select and then
press the Advance Key
‰
to enter.
• Press the Up
¿
or Down
¯
key to move through
available menu prompts.
• Press the Infinity Key
ˆ
to move backwards
through the levels: parameter to submenu; sub-
menu to menu; menu to Home Page.
•
Press and hold the Infinity Key
ˆ
for two seconds
to return to the Home Page.
Control Module Operation Page Parameters
3
[``Ai]
[oPEr]
Analog Input Menu
[```1]
[``Ai]
Analog Input 1
[`Ain]
Process Value
[`i;Er]
Error Status
[`i;Ca]
Calibration Offset
[`dio]
[oPEr]
Digital Input/Output Menu
[```1]
[`dio]
Digital Input/Output 1
[`do;S]
Output State
[`di;S]
Event State
[LiM]
[oPEr]
Limit Menu
[```1]
[LiM]
Limit 1
[`LL;S]
Low Set Point
[`Lh;S]
High Set Point
[Mon]
[oPEr]
Monitor Menu
[```1]
[Mon]
Monitor 1
[C;MA]
Control Mode Active
[`h;Pr]
Heat Power
[`C;Pr]
Cool Power
[`C;SP]
Closed Loop Working Set
Point
[`Pu;A]
Process Value Active
[Loop]
[oPEr]
Loop Menu
[```1]
[Loop]
Loop 1
[`C;M]
Control Mode
[A;tSP]
Autotune Set Point
[`AUt]
Autotune Request
[`C;SP]
Closed Loop Set Point
[`id;S]
Idle Set Point
[`h;Pb]
Heat Proportional Band
[`h;hy]
Heat Hysteresis
[`C;Pb]
Cool Proportional Band
[`C;hy]
Cool Hysteresis
[``ti]
Time Integral
[``td]
Time Derivative
[``db]
Dead Band
[`o;SP]
Open Loop Set Point
[ALM]
[oPEr]
Alarm Menu
[```1]
[ALM]
Alarm 1
[`A;Lo]
Low Set Point
[`A;hi]
High Set Point
[CUrr]
[oPEr]
Current Menu
[```1]
[CUrr]
Current 1
[`C;hi]
High Set Point
[`C;Lo]
Low Set Point
[`CU;r]
Read
[`C;Er]
Error
[`h;Er]
Heater Error
[P;StA]
[oPEr]
Profile Status Menu
[```1]
[P;StA]
Profile Status 1
[P;Str]
Profile Start
[PACr]
Action Request
[`StP]
Active Step
[S;tyP]
Active Step Type
[t;SP1]
Target Set Point Loop 1
[P;SP1]
Produced Set Point 1
[hour]
Hours Remaining
[min]
Minutes Remaining
[`sec]
Seconds Remaining
[Ent1]
Active Event Output 1
[Ent2]
Active Event Output 2
[``JC]
Jump Count Remaining
