background image

3

Thank you for purchasing the WattAge PT-19 Cornell EP ARF.  Before completing the final assembly of your new air-
plane, please carefully read through this instruction manual in its entirety.  Doing so will ensure your success the first time
around!

PT-19 CORNELL EP ARF FEATURES

Prebuilt from High-Quality Balsa, Light Plywood and Molded Plastic

Precovered with Real Iron-On, Heat-Shrink Covering Material

Scale Realism and Great Flight Characteristics In a Small Package

Prebent Wire Main Landing Gear and Steerable Tail Wheel

Molded Cowling, Windscreens and Landing Gear Strut Fairings

Includes a High-Quality Micro Hardware Package

Fast and Easy Assembly - Over 50 High-Resolution Digital Photos and Drawings to Guide You

This instruction manual is designed to guide you through the entire assembly process of your new airplane in the least amount of
time possible.  Along the way you'll learn how to properly assemble your new airplane and also learn tips that will help you in the
future.  We have listed some of our recommendations below.  Please read through them before beginning assembly.

Please read through each step before beginning assembly.

You should find the layout very complete and straightforward.
Our goal is to guide you through assembly without any of the
headaches and hassles that you might expect.

There are check boxes next to each procedure.  After you

complete a procedure, check off the box.  This will help prevent
you from losing your place.

Cover your work table with brown paper or a soft cloth, both

to protect the table and to protect the parts.

Keep a couple of small bowls or jars handy to put the small

parts in after you open the accessory bags.

We're all excited to get a new airplane in the air, but take your

time.  This will ensure you build a straight, strong and great
flying airplane.

If you come across this symbol 

,  it means that this is an

important point or an assembly hint.

INTRODUCTION

If you should find a part missing or damaged, or have any questions about assembly, please contact us at the address below:

To enable us to better serve your needs, please include your email address with any correspondence you send to us.  Your email
address will be added to our Customer Service Database so you will automatically receive free updates and tech notices for your
particular product.  You will also receive repair status updates (if applicable) and other important information about your product
as it becomes available.

IMPORTANT INFORMATION ABOUT YOUR EMAIL ADDRESS

CHECK IT OUT!

  We urge you to come check out our website at http://globalservices.globalhobby.com.  There you will find public message

boards frequented by other WattAge product owners and the WattAge support staff.  This is a great place to learn about new products, get help
and suggestions for your current WattAge products or just simply hang out and chat with people that share your same interests.

Global Hobby Distributors will not disclose the information it collects to outside parties.  Global Hobby Distributors does not sell,

trade, or rent your personal information to others . Your privacy is important to us.

In North America:

CUSTOMER SERVICE INFORMATION

Global Services

18480 Bandilier Circle

Fountain Valley, CA  92708

Phone: (714) 963-0329

Fax: (714) 964-6236

Email: service@globalhobby.net

Summary of Contents for PT-19 CORNELL EP ARF

































Reviews: