Section 2
Auto-Zone
Plus
2-18
Design Guide
Set the Zone Controller Address Switch following the following addressing
instructions.
Caution:
Incorrect addressing is the number one cause of communication
problems.
Check
the addressing carefully. Remember, the Zone
Controller only reads the switch during a power-up. If the address
switch is changed, the unit
must
be turned OFF then ON before the
new setting will be recognized.
Figure 2-13:
Zone Controller Address Switch Settings
Note:
Ignore any markings or numbers on the switch.
Use this chart!
Address Switch Shown Is
Set For Address 1
Address Switch Shown Is
Set For Address 13
Controller
Address Switch
Controller
Address Switch
ADDRESS
ADD
ADDRESS
ADD
1
1
4
4
8
8
2
2
16
16
32
32
TOKEN
TOKEN
NET
NET
ADDRESS
ADD
SW1
1
1
2
2
4
4
8
8
16
16
32
(Always OFF- Not Used)
32
TOKEN
NET
TOKEN
(Always OFF)
NET
(Always ON)
Address Switch Values
Switch Shown Is
Set For Address 5
Note:
1.) Ignore Any Markings On The Switch Body.
2.) Use The Address Charts Below Or Address Switch
Value Table Above To Determine Correct Switch Setting.
3.) Power To Controller Must Be Turned Off And
Back On In Order For Switch Settings To Take Effect.
Zone Controller Address Switch Setting
Address Switch Values
Address Switch Values Are
Added Together When The
Rocker Is Pushed Down In
The Direction Of The “ADDRESS
ADD” Arrow Marked On The Zone
Controller Circuit Board
CX6
SW1
Q3
Q2
D3
VR1
7824
GND
24VAC
R17
R16
U7
C7
R15
POWER
R21
REV
.
2
YS101
562
MDL
F1
250
D4
R26
LD3
L1
SCAN REC
R12
C6
R1
1
TOKEN
NET
LD2
32
R14
R13
R100
LD1
C5
D1
K1
V2
K2
D2
ACTUA
TO
R
R10
R9
PJ2
V1
C4
T
SHLD
R
8
16
2
4
ADDRESS
ADD
1
U6
2.)It Is Recommended That All
Controllers Address Switches Are
Set Before Installation.
3.)Power To The Zone Controller Must
Be Cycled Before Address Switch
Changes Will Take Affect.
RS-485
Communications To Next
Zone Controller
RS-485
Communications To Next
Zone Controller
Notes:
1.)AllCommunication Wiring To Be
2 Conductor Twisted Pair With
Shield. Use Belden #82760 Or
Equivalent.
R
SH
T
R
SH
T
R
SH
T
R
SH
T
All Comm Loop Wiring Is
Straight Thru
Local Loop
RS-485
9600 Baud
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
ADDRESS
ADD
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
TOKEN
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
NETWORK
1
6
11
16
12
13
14
15
2
7
3
8
4
9
5
10
firealarmresources.com
Summary of Contents for Auto-Zone Plus
