background image

9

REPLACEMENT COMPONENTS

Item

QTY

Part No.

Description

1

1

68100992

13" x 65" Black Tank- in-Tank With Base & Dome Hole with Plug 

2

1

68101076

Distributor Pipe 1.05" Diameter ABS

 

3

1

68101149

Distributor Screen for Inner Tank 3/4" MPT With 4 Screens/ 5.75" length

4

1

68101280

Distributor Adapter for Mid Plate Large Tank-in-Tank

5

1

68103002

Female Plumbing Adapter PVC SCH 40 3/4" SXF

6

1

68104871

Tank Head 1191 Without Bypass Valve Assembly

7

1

68104876

W100 Bypass Valve Assembly, Does Not Include Plumbing Adapters

8

2

68106630

WS1 Plumbing Adapter Fitting Assembly 1" MNPT (2 per Pack)

Part No. 68108439 

Funnel to fill carbon 

media through top 

of tank.

1.5" PVC Class 200 

Pipe 32" Long and  

2.5" x 1.5" SXS PVC 

Reducing Coupling

Diagram B

PART NO.

REBED KIT

68110169

Replacement Carbon and OneFlow

®

 Media

68110145

Replacement Carbon and OneFlow

®

 Media Plus Tools

Note: Before replacing any media ensure you have a wet/dry vacuum, all your media replacement tools shown in 

image above, and rebed kit ready in order to proceed.

Media Replacement Tools

Tools needed to replace E-Treat media that are not supplied by 

Watts: Standard wet/dry vacuum, and tape.

Part No. 68110144 2.5" x 1.5" Reducing Coupling used to hold 

removal tube in place (keeps removal tube from falling into 

tank) while filling OneFlow

®

 media, It also acts as a small 

funnel while filling.

Part No. 68101278 Removal and Insertion Tool for mid plate 

insert and filling tube for OneFlow

®

 media.

Part No. 68106617 1" PVC Hose 6 ft Long 

to adapt to vacuum if standard vacuum 

hose (customer supplied) is too short to 

reach bottom of tank.

Tape (customer supplied) to 

cover distributer tube when 

filling carbon media.

Summary of Contents for 68101336













Reviews: