Massage
bathtub
Massage
bathtub
Page
2
of
11
Page
9
of
11
1
、
Electricity parameter
Rated voltage
Rated electric current
Reference circuit voltage
220VAC
2200W
<4A
12V
Rated power
2
、
Electric installation
2.1
2.2
2.3
2.4
power supply's establishment should be compled with nation security standard, voltage
and frequency also shoule be accord withproduct's nameplate.Especially install creep-
age protect switch and also check whether can connect with ground.
The wire collected to the massage bathtub should be fitting permanent., and the wire
should be a three-core wire, the sectional acreage of each core cannot less than 12A.
when wire pass the wall,it should be use bushing for protection until the AC outlet.
Ground wire of bathtub should be test whether works with house appliance ground wire.
The wire end of electricity control box should connect to the control panel, water bottom
light, loudspeaker, electrical engineering and the detector protection respectively.
3
、
Water supply device
3.1
This device's hydraulic pressure is 0.2-0.4Mpa.
3.2 The water supply characteristics on the wall: The cold or hot water supplies inside the
bathroom also establish in the shelter of the massage tub, use the hose to connect with
the cold or hot joint of the tub. the pipe towards is decide by the customer, the machine
do not go with the hose.
4.1
4.2
4.3
4.4
4.5
Before install, must consider the place of install massage bathtub whether can support
this device's pressure.
Place the massage bathtub on the install position, adjust level to make the drain system
smooth.
Adjust the leg's screw to make sure all of the screw touch ground completely.
Install the drain hose, and make some measure to against on the connecter.
Fix cold and hot water-pipe well, then install the showerhead. And then put drain into
downcomer, finally connect with power and make sure whether device connected with
ground can work.
5
、
Using Method
4
、
Installation introduction
5.1
5.2
5.3
Turn on faucet, adjust water's temperature, add water to the massage bathtub.when the
highest water level exceed the highest nozzle about 20-30mm and reach the detector,
press the switch button to let the electric machine.
Revolve the adjust switch ,and choose the proper surf pressure.
After finishing if should turn off pump at first, then open drain button,when water is all out ,
please make a clean of bathtub to keep in good.
6
、
Clean and keep in good condition
.
.
6. 1 us ua lly us e sof t clot hs an d ge ne ral liqu id clea ns er can wa sh aw ay di rt , bu t for bi d to us e the
clea ns er wi th ac et on e or the ammon ia comp os ition ;wh en di sinf ec t, for bi d to us e the di sinf ec tor
con tai ne d the for mal de hy de .
6. 2 the di rty spo t of sur fac e can us e the too thp as te to wi pe wi th the sof t clot h
6. 3 to the low -gr ad e cha fe of the sur fac e or bu rne d by ciga ret te, can soa k in wa ter to wh et wi th 20 00 #
lev iga tion san d pa pe r, the n po lishi ng .
6. 4 If the el ec trop lat e pi ec e con tai n stai n, us e the sof t clot h to wi pe ligh tly, av oi d to wi pi ng wi th coa rse clot h
6. 5 of ten clea n up the ba ckwa ter ne t cov er, pr ev en t it from stop ;
6. 6 Ch ec k wh et he r ha ve br ea k on pi pe an d wa ter wa y ap er iod ical ly.
7.3.2Press “ ”to decrease the length of one step (the length
of one step =100KHz). Press this button over 2 seconds, the system
searches the radio stations of smaller frequencies automatically;
the digital phase locked loop will lock the FM station automatically
and the liquid crystal shows the frequency of this station; When it
reaches to the limit of 87.5MHz, press this button again and the
frequency jumps to 108.0MHz.
7.4When the FM radio is on, press “ ”till the LCD blinks “VOL”
and Numbers, and then press“ ” to increase the volume and
press “ ”to decrease the volume. The volume adjusting range
is 0-20, and 21 in total.
7.5Station storage/select
7.5.1 Station storage
：
when FM function is on and select the station
frequency to be stored, press “ ” for 2seconds to select the
location for storage “CH” shall blink, and press “ ”to choose
the location; press the icon “ ”again, the station frequency
shall be stored in the selected storage location.
7.5.2 Station select
：
When FM function is on
，
press “ ”the
corresponding stored station can be selected while LCD displays
the corresponding storage location number and “CH”, 5 seconds
later, LCD displays the volume.
8Bluetooth Audio Play
8.1When the system is on and the audio play is off, press“ ”
for 2 seconds to check the Bluetooth device and the paring code
(LCD scrolling displays the Bluetooth device name and paring code)
and then press “ ”again for 2 seconds to set up the Bluetooth
deviceand the paring code (LCD scrolling displays the Bluetooth
device name and paring code).During this time, press “ ”to
exit the state (it will be exit automatically of non-press after 12 seconds)
