background image

WMO2 G900 / G1800 / G1900

WCOM/GSM/WMO2/WMO2ATDOC

Friday 21 May 1999

WAVECOM confidential ©

18

3.1.1

 

Request syntax

3.1.1.1

3.1.1.1

 

Basic syntax

Basic syntax

At fixed baud rate uppercase or lowercase letters can be used to

type in the AT-Commands. But the use of both upper and lower-

case characters in the same command is not permitted.
The end character, except in some cases for which it is indicated, is

always the <CR> (Carriage Return) character.
The syntax is based on the nominal Hayes standard:

 

Each command begins with a 2 letters prefix "AT" (ATtention)
except the "+++" and the "A/" commands;

 

The command's body is a single character or an
& (ampersand) character immediately followed by a single

character;

 

A + (plus) character may immediately follow the AT prefix to
indicate it is an extended command format in that case, a

letter (chosen among the following one: A, C, D, E, F, G, I, M,

S, T, V or W) immediately follows the + character, then comes
the command itself (the body);

 

The parameters (if any) of the command 

are placed 

at the end.

Examples:
ATA

' to answer a call.

AT&W

' to store the profile in memory.

ATQ1

' to suppress the extended syntax result codes.

ATS0=2

' to automatically answer a call after 2 rings.

It is possible to concatenate several commands on the same

command line, example: ATQ1S0=2;&W

You must insert a ; (semicolon) straight after each command that
use a = (equal) or ? (question mark) character and after each

extended format command.

There is no need of any special character for all other commands

(i.e. there are no ; (semicolon) between the Q1 and S0=2

commands above, but there is one straight after the S0=2

command before the &W command.

3.1.1.2

3.1.1.2

 

Special cases

Special cases

If the serial link exchange baud rate is not fixed, case of the modem

working in autobauding mode, it is not possible to type in the

commands using lowercase characters.
When sending SMS messages, the end character is no longer the

<CR> (carriage return), it is the <CTRL>Z character (Escape

character).

Summary of Contents for WMO2

































































































Reviews: