background image

PIN NO.

SYMBOL

DESCRIPTION

1, 17

3.3V

Power positive (3.3V power input)

2, 4

5V

Power positive (5V power input)

3, 5, 7, 8, 10, 11, 12, 13, 15, 16,
18, 24

NC

NC

6, 9, 14, 20, 25

GND

Ground

19

TP_SI

SPI data input of Touch Panel

21

TP_SO

SPI data output of Touch Panel

22

TP_IRQ

Touch Panel interrupt, low level while the Touch Panel
detects touching

23

TP_SCK SPI clock of Touch Panel

26

TP_CS

Touch Panel chip selection, low active

Resource

Driver

If the touch screen doesn't work properly, please install the driver: LCD-show-170703.tar.gz, but not

LCD-show-161112.tar.gz.

LCD-show-170703.tar.gz (network connection is required while installing)
(http://www.waveshare.com/w/upload/0/00/LCD-show-170703.tar.gz)
LCD-show-161112.tar.gz (http://www.waveshare.com/w/upload/4/4b/LCD-show-161112.tar.gz)

Image

RPi-3.5inch-HDMI-LCD-Raspbian_480x320-170510.img.7z (https://drive.google.com/open?
id=0BwbgcecjOmBqdk5qOVJCMlJKcVk)
RPi-3.5inch-HDMI-LCD-Raspbian_800x480-170510.img.7z (https://drive.google.com/open?
id=0BwbgcecjOmBqZWloaG4yaVQzRms)

Demo video

Demo video (https://youtu.be/IfNH5s7vLbI)

Software

Panasonic SDFormatter (http://www.waveshare.com/w/upload/d/d7/Panasonic_SDFormatter.zip)
Win32DiskImager (http://www.waveshare.com/w/upload/7/76/Win32DiskImager.zip)
PuTTY (http://www.waveshare.com/w/upload/5/56/Putty.zip)

General Tutorial Series

Raspberry Pi Tutorial Series

FAQ

Summary of Contents for WSH-12824








Reviews: