Stromfunktion steht. “FErr” wird angezeigt.
Echt-Effektivwertmessungen: Modelle 2020 und 2030 sind AC
gekoppelte Echt-Effektivwert-messende Geräte.
Sie messen den echten
Effektivwert, auch von verzerrten Strom- und Spannungs-Wellenformen. Der
Crest-Faktorbereich wird in Tabelle 1 gezeigt. Der Crest Faktor ist der Spitzenwert
geteilt durch den Effektivwert.
Echt Effektivwert (AC + DC) Messungen:
❶
Meßkabel wie in Figur 1 gezeigt
verbinden.
❷
Funktionsschalter auf A
stellen. Zweite Funktionstaste
drücken um Echt-Effektivwertmessung (AC + DC) zu aktivieren. AC und DC
Symbole werden angezeigt.
❸
Wie unter Punkt 3 oben weiter messen. Das Gerät
sperrt den Bereich gemäß höchstem Eingangssignal. Steigt die Spannung über
diesen Bereich hinaus (OL Anzeige), höheren Bereich mit
✔
RNG
Menüfunktion
wählen
(Siehe Menüfunktionen, Seite xx).
Eventuell von mA Eingang nach A
Eingang wechseln. (Messung zuerst unterbrechen und Meßkabel vom Schaltkreis
trennen.
E • Medidas de Corriente CC y CA (vea Fig. 2)
❶
Conecte la punta de prueba roja a la entrada de 100 mA para medidas de
corriente hasta 100 mA, o a la entrada de 10A para medidas hasta 10 A
(up to 20A
can be measured for max 30s)
. Conecte la punta de prueba negra a la entrada
COM.
❷
Ponga el selector de función en la posición A
o A
❸
Abra el
circuito sometido a prueba y conecte las puntas de prueba en serie con la carga.
❹
Conecte la alimentación del circuito.
➎
Lea el valor de la corriente en el
visualizador.
Aviso de entrada incorrecta:
El zumbador avisa si se ha conectado la punta
de prueba a una entrada de corriente y el selector no está en una escala de
corriente.
“FErr” is displayed.
Medidas de verdadero valor eficaz en CA:
Los modelos 2020 y 2030 son
medidores de verdadero valor eficaz (TRMS), acoplados en CA. Miden el
verdadero valor eficaz de señales distorsionadas de tensión o corriente CA. En la
Tabla 1 se indica la capacidad de manejo de factores de cresta. El factor de cresta
es la tensión de pico dividida por la tensión eficaz.
True RMS (AC + DC) Measurements:
❶
Connect test leads as shown in
figure 1.
❷
Turn function selector switch to A
. Press second function key
to activate true RMS (AC + DC). The AC and DC symbols are displayed.
❸
Continue as under step 3 above. The meter range locks for highest AC signal
input. If the current is too high (OL displayed), select
✔
RNG
and up range until a
reading appears (see Menu Functions). Eventually change from mA to A input
(disconnect meter first).
F • Mesure de Courant CC et CA (voir fig. 2)
❶
Connectez le cordon rouge à l’entrée 100mA pour mesures jusqu’à 100mA et à
l’entrée 10A pour mesures jusqu’à 10A (max 20A peuvent être mesurés pendant
max 30 secondes). Connectez le cordon noir à l’entrée COM.
❷
Placez le
sélecteur sur A
ou A
.
❸
Ouvrez le circuit à mesurer et connectez les
– 15 –
2020/30.Man.3x5,25/XPr 19/06/97 14:36 Page 17