background image

Specifications 

 

Intel NUC computer, with an AC/DC power adapter 

 

Linux operating system 

 

4 GB RAM 

 

32 GB solid state drive 

 

Ethernet port 

 

4 USB ports 

 

Belkin USB-to-Serial Portable Adapter, as required, per serial port connection 

Installation 

To install the STG, you may need the following: 

 

Rauland Responder 5 or Rauland Responder 5000 Server on same LAN as STG.  Responder 5 and 
Responder 5000 will be referred to interchangeably in this document as Responder. 

 

Brekeke SIP Server™ on same LAN as STG 

 

Configure Responder and Brekeke SIP Server per Rauland instructions.  You will find a suggested 
Brekeke SIP Server Dialplan information below. 

 

Windows PC running the WaveWare Discover and Reset Tool, connected to LAN, for purposes of 
discovering the STG on the LAN (only required if using DHCP to assign an initial IP address to the 
STG, or if the static IP address is incompatible with the LAN the STG is connected to.   

 

An Ethernet controlled paging system and/or up to four serial port controlled paging systems or 
downstream devices that process TAP protocol.  Note: When connecting WaveWare paging 
systems to the STG USB ports, you will need a Belkin USB-to-Serial Portable Adapter for each 
paging system. 

 

UPS (uninterruptible power supply).  A UPS can reduce the instances of potential disk corruption 
or disk cleanup processes that might be required after a sudden loss of power event. 

The STG should be installed using the following procedure: 

 

Before powering up the STG, make all of the connections, including: 

o

 

Ethernet 

o

 

One Belkin USB-to-Serial Portable Adapter per serial port connection 

 

Power up the STG.  Wait a few minutes for the STG to boot up.  The STG is designed to boot up 
automatically when power is applied.  The boot up method is adjustable in the BIOS, which is 
documented in the Troubleshooting section. 

Configure Static IP Address 

The STG ships with DHCP enabled, so that it can obtain a dynamically assigned IP address when it is 
connected to a LAN.  The STG requires a static IP address assignment in order to have uninterrupted 
operation monitoring the Responder alerts.  Use the following procedures to set a static IP address in 
the STG. 

Summary of Contents for STG



















Reviews: