background image

8

OPTIONAL ACCESSORIES

•  15-foot hardwire kit connects the 

unit  directly  into  your  12-volt 

power  system  (recommended  for 

installation  only  by  a  qualified 

automotive accessory installer).

•  30-foot  temperature  sensor  for 

vehicles requiring a longer sensor 

cable.

Each  is  available  for  an  additional 

charge  by  calling  our  customer  ser-

vice  department  at  (888)  422-6672 

from  anywhere  in  the  U.S.A.,  (707) 

566-2260,  or  by  e-mail  at 

customerservice@pincorp.com.

FREQUENTLY ASKED 

QUESTIONS

How does the Wayfinder V2000 

work?

Developed  by  PNI  Corporation  for 

the  U.S.  military,  the  patented  mag-

netic  sensor  technology,  called  mag-

neto-inductive, is the greatest advance 

in  compass  technology  in  60  years. 

It  senses  the  difference  between  the 

magnetic  fields  of  the  earth  and  your 

vehicle,  then  electronically  subtracts 

the latter to display accurate compass 

readings. This superior performance is 

achieved with reduced power consump-

tion and at a lower cost. The technol-

ogy is so advanced, it has been adopted 

for compasses in GM, Ford, and Chrys-

ler automobiles, Polaris jet skis, Bay-

liner boats, and Timex watches.

Where can the Wayfinder 2000 be 

used?

You’ll find it a valuable help to navi-

gation in any type of vehicle, includ-

ing cars, trucks, vans, SUVs, off-road 

vehicles, boats, and RVs.

What is calibration, and why is it 

necessary?

Calibration  permits  the  Wayfinder 

V2000  to  distinguish  between  the 

earth’s magnetic field and stray mag-

netic  fields  such  as  those  generated 

Summary of Contents for V2000

















Reviews:

Related manuals for V2000