background image

2

and losing memory settings.

•  Keep  the  unit  plugged  into  your 

vehicle while changing the battery 

to avoid losing memory settings.

•  Since not all vehicles supply con-

stant power to the lighter socket, 

a battery must be in the unit at all 

times to retain memory settings.

•  Unit shuts off automatically about 

10  minutes  after  the  last  detected 

change  in  magnetic  field.  During 

night  use,  a  built-in  light  sensor 

automatically switches on the screen 

backlight (disabled when the unit is 

operating on its battery alone).

Step 3: Install the temperature 

sensor.

Mount the sensor inside for monitor-

ing  interior  temperatures  or  outside 

for exterior temperatures (required for 

ICE alert feature). If used inside, place 

the sensor in a natural airflow, out of 

direct sunlight, and not in the direct 

outflow  of  a  vent.  For  exterior  use, 

select a ventilated location outside the 

passenger  compartment,  such  as  the 

grill  area  or  doorjamb  (away  from 

sunlight and engine heat).
Making sure the surface is free of dirt, 

use the peel-and-stick pad to adhere 

the sensor. Mount to a less heat-con-

ductive  plastic  or  rubber  component 

instead of to a steel body part. (As all 

vehicles are different, you may need 

to experiment to find the best site.)
Use  the  included  retainer  clips  to 

secure the sensor cable to the wind-

shield or dashboard. Plug the sensor 

connector  into  the  jack  marked 

“TEMP” on the back of the compass.

Note:

  A  longer  30-foot  temperature 

sensor  is  available  (see 

Optional 

Accessories

 on page 8).

Note:

  Do  not  leave  the  Wayfinder 

V2000  in  a  parked  vehicle  that  is 

likely to be exposed to extremely hot 

or cold temperatures.

Summary of Contents for V2000

















Reviews:

Related manuals for V2000