background image

7

ICE alert

When the exterior sensor is properly 

installed,  the  Wayfinder  V2000  can 

alert  you  to  dangerous  road  con-

ditions.  Any  time  the  temperature 

drops to 35ºF (2ºC), it automatically 

switches  to  temperature  mode  and 

“ICE”  will  flash  in  the  bottom  right 

corner  along  with  the  temperature. 

This  is  shown  until  any  button  is 

pressed.  (ICE  alert  feature  will  not 

work if the temperature sensor is not 

installed or is installed incorrectly.)

Adjusting the screen backlight

Press 

 to switch on the backlight. 

When operating on the internal battery, 

the backlight has been set to shut off 

automatically  after  10  seconds,  con-

serving power. To change this setting:
1.  Hold 

 

“PRESS  AGAIN  TO  STEP,” 

“HOLD  LIGHT  TO  SELECT” 

cycles in the lower right corner.

2.  Press 

 

The values 00, 10, 30, 60, and 180 

seconds appear in sequence.

3.  Hold 

 

To select the desired interval until 

“DONE” displays. Note: selecting 

00 disables the auto shut-off fea-

ture.

4.  Press 

 

The backlight remains on for the 

selected time, then shuts off.

When  using  the  12-volt  adapter  or 

optional hardwire kit, the built-in light 

sensor overrides the auto-shutoff func-

tion. Now the backlight operates when-

ever  the  compass  is  on  in  low-light 

conditions such as night. It will switch 

off whenever no magnetic field change 

has been detected for about 10 minutes, 

or when you press the 

 button.

Summary of Contents for V2000

















Reviews:

Related manuals for V2000