17
November 1992
Part No. 917543 Rev. A
TABLE 3-1. DEFINITION OF DUPLEX II COMPUTER FAULT CODES
CODE
STATUS
DESCRIPTION
01
1
Push to start open, or cash or credit switch(es) shorted.
02
1/3*
Push button start; option disabled but switch detected.
03
1/2*
Unit has overrun prepay/preset amount.
04
1
ROM error.
05
1/2*
Pulser error. (Set if jitter count exceeds limit)
06
1/3*
Illegal current sensed in valve or relay output circuit.
08
1/2/3*
Time out limit has been exceeded.
10
1/2*/3
Reverse pulse limit has been exceeded.
11
1
Corrupted option data. The pump will not restart until
Option 99 is set to 03. Cycling power will not reset this error.
12
3
Corrupted totals data; the totals were reset to zero.
13
3
Corrupted unit price data; the unit prices were reset to zero.
14
1/2*
Forward pulses from illegal pulser.**
15
1/2*
Jitter pulses from illegal pulser.**
16
1/2*
Reverse pulses from illegal pulser.**
20
3/4*
Jitter count exceeds limit (blenders only).*** †
21
3/4*
Reverse count exceeds limit (blenders only).*** ††
51
1
Blend ratio has exceeded error limits in Option 52.***
Note:
An asterisk (*) next to a number in the Status column indicates the default
status for that Fault Code. More than one number in the status column indi-
cates that the status of that Fault Code is alterable. The fault status of an
alterable code must be selected in accordance with the code allocation pro-
gramming sequence in Option 98. See Programming for the Duplex II Com-
puter—Service (part number 917479) for specific information.
**
An illegal pulser is defined as follows:
1) Blending dispensers - a pulser for a feedstock product not selected.
2) Unihose MGDs - a pulser for a product not selected.
***
Because these are blend errors they should not appear on non-blending dispensers;
however, if the computer is programmed incorrectly, for instance if it is set up as a
blender, these errors could appear in a non-blending dispenser.
†
Jitter pulse count exceeds logging limit fault is displayed in the following special format:
Sale Amount:
NNN-SS
Sale Volume:
PF.20.BB
where, NNN =
Sequence Number
S
=
Side 1 or Side 2
P
=
Product Source (0-7)
F
=
Fault Source (0-7) or (H or L)
20
=
Fault Code 20 (Jitter count exceeds limit)
BB
=
Maximum jitter count allowed
††
Fault Code 21 is displayed in the same special format as Fault Code 20 except that
21 appears in the Sale Volume. Example: PF.21.BB
Summary of Contents for Vista Series
